805739 Mercruiser HOSE


805739 HOSE Mercruiser 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND HOSE
805739 HOSE Mercruiser
Rating:
103

Buy HOSE 805739 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
 
$84.98
 

29-08-2017

Arc Remanu: Arc Remanufacturing
ARC 80-5739 Drive Shaft
CV threads and splines renewed 100% for perfect installation and fit||Center shafts are tested for run-out to insure full radius straightness and replaced when necessary.||Essential hardware including dust shields, slingers and nuts are replaced with new OEM quality parts as required
Number on catalog scheme: 20
 

Mercruiser entire parts catalog list:

40420001D 1998
428B116KD 1997,1998
442B110GD 1994,1995,1996,1998
442B115KD 1997
4A72040ND 1998
4C8204DLD 1998
4CJ2040ND 1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 298-5564 T40 Torx Socket 1
B 268-1968 Pry Bar 1
C 370-8376 Capping Kit 1 Start By:
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft - Remove" for the correct procedure.
Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove" for the correct procedure.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Use a deep socket in order to remove the electrical connections from the electronic unit injectors. Use of incorrect tooling will result in damage to the electronic unit injectors.
Note: Place identification marks on all hoses, on all hose assemblies, on wires and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. Plugging all hose assemblies and tube assemblies will prevent fluid loss. Plugging all hose assemblies and tube assemblies will keep contaminants from entering the system.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g01971774
Place a suitable container below tube assembly (1) to catch any fuel that might be spilled.
Loosen the nut on hose assembly (3) to allow the fuel to drain from tube assembly (1).
Remove hose assembly (3) from tube assembly (1). Remove O-ring seal (2).
Use Tooling (C) to cap the hose assembly immediately. Use Tooling (C) to plug the tube assembly immediately.
Illustration 2 g01971773
Make a temporary mark on valve bridges (5) to show the location and orientation. Remove valve bridges (5).Note: Identification will ensure that the valve bridges can be reinstalled in the original location and the original orientation.
Remove seal (4) from the cylinder head and electronic unit injector (8).
Make a temporary mark on wiring harness assembly (6) to show the location and orientation.
Use a deep socket to remove connections (7) from electronic unit injector (8).
Use Tooling (A) to remove Torx screw (9) from clamp (10). Discard the Torx screw.Note: Tooling (A) must be used to ensure no damage to the electronic unit injector.
Illustration 3 g01971775
Illustration 4 g01972153
Make a temporary mark on electronic unit injector (8) to show the original location of the electronic unit injector.
Temporarily remove Tooling (C) from the electronic unit injector.
Use Tooling (B) to pry beneath clamp (10) and free electronic unit injector (8) from the cylinder head.Note: Always handle electronic unit injectors with care.
Immediately replace Tooling (C) onto the electronic unit injector.
If electronic unit injector (8) is to be reused, Follow Step 17 through Step 19 to remove sealing washer (12) and O-ring seal (11).
Use a suitable tool to remove sealing washer (12) from electronic unit injector (8). Ensure that the sealing washer is removed from the cylinder head.Note: Ensure that the nozzle for the electronic unit injector is not damaged in any way on removal of the sealing washer.
Install Tooling (C) to the nozzle for electronic unit injector (8) and the open port of the electronic unit injector.
Remove O-ring seal (11) from electronic unit injector (8).
If necessary, repeat Step 7 through Step 19 to remove the remaining electronic unit injector.
Illustration 5 g02311716
If necessary, follow Steps 21a through 21f to remove harness assemblies (6) from cylinder head (16).
Cut cable straps (13).
Unscrew the remaining sections of the cable straps from the cylinder head.
Disconnect harness assembly (15) from harness assembly


Parts hose Mercruiser:

806222 16
 
806222 16 HOSE
02602347, 02608427, 257B021JS, 40420001D, 4211015L1, 4231017L1, 4262C01JT, 4332087N1, 4350100KS, 4350104JS, 4350104KS, 4350111HS, 4350118JS, 4350118KS, 442B110GD, 442B115KD, 443B1003S, 443B100JS, 443HC00JT, 4441027LE, 444106AM1, 444106LPS, 444236HRS,
806221 42
 
806221 42 HOSE ASSEMBLY, (84.00 Inches Bulk), Return
02602347, 02608427, 257B021JS, 40420001D, 4111021L1, 411102KN2, 4211015L1, 4231017L1, 424106LRS, 4262C01JT, 430B00001, 430L000JS, 4332087N1, 4350100KS, 4350104JS, 4350104KS, 4350111HS, 4350118JS, 4350118KS, 442B110GD, 442B115KD, 443B1003S, 443B100JS,
19833 89
 
19833 89 HOSE
40420001D, 40500006T, 40500010T, 40500010U, 40500120U, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND, 4M4102LTS
805741
 
805741 HOSE
40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND
805743
 
805743 HOSE
40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND
883972
 
883972 HOSE-TRANS. OIL COOLER TO EXH. ELBOW
428B116KD, 442B115KD, 4A72040ND
855496
 
855496 HOSE-TRANS. OIL COOLER TO EXH. ELBOW
40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
889508
 
889508 HOSE
4C72040TD, 4CJ2040ND
Back to top