854173 Mercruiser ELBOW


854173 ELBOW Mercruiser 40280001D, 40280002D, 40420002D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4CJ2040ND ELBOW
854173 ELBOW Mercruiser
Rating:
13

Buy ELBOW 854173 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$1,355.35
 

09-08-2022

-: -
Yamada Pump Part 854173
Yamada Pump Part 854173
Number on catalog scheme: 19
 

Mercruiser entire parts catalog list:

40280001D 1998
40280002D 1998
40420002D 1998
428B116KD 1997,1998
442B110GD 1994,1995,1996,1998
442B115KD 1997
4A72040ND 1998
4C72040TD 1998
4CJ2040ND 1998

Information:

1. Remove two bolts. Remove upper pump manifold (2). Check condition of O-ring and replace as necessary. Use 1U6395 O-ring Assembly Compound at assembly.2. Disconnect coolant fitting (3).3. Loosen two hose heater clamps and remove two hoses (4).4. Remove two bolts on pump end of lower pump manifold (5) and remove clamp from other end. Remove or rotate manifold away from pump. Check condition of o-ring. Replace as necessary. Use 1U6395 O-ring Assembly Compound at assembly.5. Loosen two lower radiator hose clamps and slide hose (6) away from pump. 6. Remove seven bolts marked "X" and remove water pump (1). The weight of the pump is 27 kg (60 lb). For installation of pump, replace all gaskets and reverse the order of the removal steps.End By:a. fill coolant to correct levelDisassemble Water Pump
Start By:a. remove water pump 1. Remove four bolts. Remove water pump manifold. The water pump seal can be replaced without removing the water pump from the engine.An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not an indication of a water pump seal failure. This is required to provide lubrication for the seal. Replace the water pump seal only if a large amount of leakage or a constant flow of coolant is observed draining from the water pump housing.2. Remove O-ring seal (1) from the adapter.3. Remove adapter (2) from the housing. Remove the O-ring seal from the outside diameter of the adapter.4. Remove bolt (3) and the retainer that hold the impeller on the shaft. 5. Use tooling (A) to remove impeller (4) from the shaft. 6. Remove the spring and seal (5) from the shaft. 7. Remove four bolts (7) from retainer (6) that hold the shaft assembly to the pump housing.8. Remove O-ring seal (8) from the housing. 9. Remove gear and shaft assembly (10) from the housing.10. Remove bolt (9) and the retainer from the shaft assembly. 11. Use a press to remove the shaft assembly from gear (11). Remove the retainer from the shaft assembly. 12. Remove bearing (13), spacer (14) and bearing (12) from the shaft. 13. Remove lip-type seal (15) from the housing.14. Turn the housing over, and remove ceramic ring (16) and the seal.Assemble Water Pump
1. Use 6V1541 Quick Cure Primer to clean shaft (8) and the seal counterbore in the pump housing.2. Install bearing (4), spacer (3) and bearing (2) on shaft (8).3. Put retainer (1) and gear (7) in position on the shaft assembly. Install retainer (6) and bolt (5). 4. Use tooling (A) to install the lip seal in the housing as shown. Put a small amount of clean SAE 30 Oil on the lip of the seal. 5. Install a new O-ring seal (10) on the housing.6. Put shaft assembly (9) in position in the housing. Install the bolts that hold the retainer to the housing.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
7. Put ceramic ring (12) in position in rubber seal (11). Use hand pressure and tool (B) to install the ceramic ring in the housing.
Avoid contaminating the seal faces with grease or oil. Also, avoid stretching the rubber seal during installation.
The carbon seal assembly must rotate with the water pump shaft after installation.8. Remove the spring from seal assembly (13). Use hand pressure and tool (B) to install the seal assembly. Push the seal assembly on the shaft until the seal faces make light contact. 9. Install spring (15) on the shaft.10. Put impeller (14) in position on the shaft. Install the washer and bolt that holds it. Tighten the bolt to a torque of 39 3 N m (29 2 lb ft). 11. Install O-ring seal (17) on the outside diameter of the adapter. Put a small amount of clean SAE 30 Oil on the O-ring seal.12. Install O-ring seal (18) on the adapter.13. Put adapter (16) in position on the housing. 14. Install water pump manifold and four bolts.End By:a. install water pumpb. add coolant to the correct level


Parts elbow Mercruiser:

63835
 
63835 ELBOW, HOSE TO TRANSMISSION (45 DEGREE)
02287333, 02297343, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 08986342, 228801, 37011856, 428B116KD, 442B110GD, 442B115KD, 4441027LE, 444106AM1, 473B1F0GS, 4A72040ND, 4M11025RS, 4M11025TS, 4M11025TT, 4M11025US, 4M31027LS
63825
 
63825 ELBOW, ADAPTOR TP BASE (90 DEG.)
01701335, 02602347, 02608427, 03302336, 03307332, 03308333, 04544347, 04856332, 04881333, 06661346, 30001854, 32001876, 37011856, 4052110CR, 44031854, 442B110GD, 442B115KD, 4454110AS, 45021102S, 474H110AR
48872
 
48872 ELBOW, BUSHING TO HOSE (45 DEG. )
03307332, 03308333, 04544347, 04856332, 06661346, 442B110GD, 442B115KD, 44541101S, 4454110AS, 473B1F0GS, 474H110AR
35580
 
35580 ELBOW-TRANSMISSION OIL COOLER
40430002S, 428B116KD, 442B110GD, 442B115KD, 444106LPS, 444236HRS, 4A72040ND, 4M4102LPS, 4V71222PD, 4V71222TD
855517
 
855517 ELBOW-TRANSMISSION
40280001D, 40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
803174
 
803174 ELBOW-OIL COOLER
40280001D, 40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND
803608
ELBOW-EXHAUST
803608 ELBOW-EXHAUST
40280001D, 40280002D, 40420001D, 40420002D, 428B116KD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD
803609
ELBOW-EXHAUST
803609 ELBOW-EXHAUST
40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND
Back to top