865208T01 Mercruiser HOSE ASSEMBLY, 3 Bib Orfice Meter


865208T01 HOSE ASSEMBLY, 3 Bib Orfice Meter Mercruiser 40500006T, 40500010T, 40500010U, 40500120U, 4M4102LTS, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE HOSE
865208T01 HOSE ASSEMBLY, 3 Bib Orfice Meter Mercruiser
Rating:
93

Buy HOSE ASSEMBLY, 3 Bib Orfice Meter 865208T01 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Information:

Introduction
This Special Instruction outlines the rework procedure for the engine timing chain on certain 306 and 307D Excavators.Do not perform any procedure that is outlined until you have read the information in this publication. Do not order and parts until you understand the information that is contained in this publication.End user must inspect the timing chain at every 1000 hours as per the Operation and Maintenance Manual instruction.Safety
Work safely. Most accidents that involve product operation, maintenance, and repair are cause by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs.A person must be alert to potential hazards. This person must also have the necessary training, skills, and tools in order to perform these functions properly.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance of a potential hazard.Therefore, the warning in this publication and the warnings that are on the product are not all inclusive. Avoid using a tool, procedure, work method, or operating technique that is not recommended by Caterpillar. If used, ensure the safety of the operating personnel and others.Ensure that the product will not be damaged or made unsafe by the operation, lubrication, maintenance, or repair procedure that are used.
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility.
Required Parts
Table 1
Required Parts    
Item    Qty    Part Number    Description    
1     1     190-5763     Guide Plate (1)    
2     1     190-5764     Tension Lever (1)    
3     1     390-8680     Timing Chain (2)    
4     1     139-7904     Oil Jet (1)    
5     1     190-5759     Seal (1)    
6     1     139-7903     Bolt (1)    
( 1 ) After failure only
( 2 ) Before/After failure onlyRequired Tools
Table 2
Required Tooling    
Qty    Part Number    Description    
1     383-1496     Yoke Holder    
1     383-1512     Holder Pin    
1     383-1515     Removal Tool    Rework Procedure
Illustration 1 g03714544
Park the machine on level ground with the implements lowered. Refer to Illustration 1.
Release the pressure from the system.ReferenceDisassembly and Assembly, RENR9437, "System Pressure - Release" in order to prepare the 306 for this rework procedure.ReferenceDisassembly and Assembly, RENR9744, "System Pressure - Release" in order to prepare the 307D for this rework procedure.
Ensure that the engine has cooled down sufficiently before beginning the rework procedure.
Illustration 2 g03714550
(1) Guide plate (2) Tension lever (3) Timing chain tensioner (4) Oil jet (7) Surface (8) Surface
If an inspection reveals that timing chain (3) has been extended within 22 - 25 mm (0.87 - 0.98 inch), replace timing chain only.
If an inspection reveals that timing chain (3) is extended to or beyond 26 mm (1.02 inch), replace timing chain and remove engine front timing gear case. Inspect guide plate (1) and tension lever (2) .
Replace guide plate (1) and tension lever (2) if cracking or flaking is observed on surfaces (7) and (8) .
Replace oil jet (4) if it has been damaged.
Replace front seal (5) .
Apply a bead of sealant (ThreeBond 1207C or equivalent) to the front plate mounting surface of the timing gear case evenly and without any breaks.
Install the timing gear case within 15 minutes of applying the sealant. Be careful not to dislodge the sealant.
Retighten the crankshaft pulley mounting bolt to 323 N m (238.2 lb ft).
Retighten the timing gear case mounting nut to 23 N m (17.0 lb ft).
Retighten the timing gear case mounting bolt to 7 - 10 N m (5.2 - -7.4 lb ft).ReferenceMitsubishi Diesel Engine, KENR5078, "Engine", "Replacement of Timing Chain"


Parts hose Mercruiser:

866331
 
866331 HOSE, Cut to 2.75 Inches
40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 424106LUS, 424106PUU
806173 82
 
806173 82 HOSE, (58.00 Inches Bulk)
40500006T, 40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 424106LTT, 424106LUS, 424106PUU, 4M4102LTS, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
863489
 
863489 HOSE, Power Steering Cooler To Check Valve
40430002S, 40500006T, 40500010T, 40500010U, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS
864579
 
864579 HOSE, Check Valve To Thermo Housing
40430002S, 40500006T, 40500010T, 40500010U, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS
864953
 
864953 HOSE, Heat Exchanger to Port Elbow
40500006T, 40500010T, 40500010U, 444236HRS, 4M4102LRS, 4M4102LTS
864966
 
864966 HOSE, Tee Fitting to Starboard Elbow
40500006T, 40500010T, 40500010U, 444236HRS, 4M4102LRS, 4M4102LTS
865317T02
 
865317T02 HOSE ASSEMBLY, 2 Bib Orifice Meter
40500010U, 40500120U, 4S420P8UE
Back to top