865409 HOSE, Drain Fitting to Thermostat Housing Mercruiser
40500006T, 40500010T, 40500010U, 4M4102LTS
HOSE
Price: query
Rating:
Mercruiser entire parts catalog list:
40500010T 1998
40500010U 1998
4M4102LTS 1998
Information:
Start By:
Install the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
Connect the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".Note: Install caps and plugs on all openings in order to prevent dirt or debris from entering the system. Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal components.Note: The following procedure outlines the removal of two sections of the exhaust manifolds. The same procedure can also be used for the removal of the remaining sections of the exhaust manifolds.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Illustration 1 g00616730
Apply 1U-8265 Penetrating Oil to the threads of four bolts (1). Then apply 4C-5593 Anti-Seize Compound to the threads of four bolts (1) .
Remove four bolts (1) and the locknuts.
Remove bolts (4), the washers, and the spacers that fasten exhaust manifold (2) and gasket (3) (not shown) to the cylinder head.
Illustration 2 g00610004
Illustration 3 g00616729
Remove exhaust manifold (2) and gasket (3) .
Remove two exhaust manifold sleeves (5) and exhaust seal (6) .
If necessary, apply 1U-8265 Penetrating Oil to the threads of four bolts (8). Then apply 4C-5593 Anti-Seize Compound to the threads of four bolts (8) .
Remove four bolts (8) and the locknuts.
Remove bolts (9) (not shown), the washers, and the spacers that fasten exhaust manifold (7) and the gasket to the cylinder head.Note: Repeat this procedure for the remaining sections of the exhaust manifold. If necessary, remove the turbochargers. Refer to Disassembly and Assembly, "Turbochargers - Remove" for the correct procedure.Installation Procedure
Note: Verify that all of the components of the exhaust manifold are clean and free of foreign material prior to installation.Note: The following procedure outlines the installation of two sections of the exhaust manifolds. The same procedure can also be used for the installation of the remaining sections of the exhaust manifolds.Note: Replace all of the high temperature nuts, bolts, and gaskets with new parts.
Illustration 4 g00616729
Illustration 5 g00610004
Position exhaust manifold (7) and the gasket for installation.
Apply 5P-3931 Anti-Seize Compound to the threads of bolts (9) (not shown), and the faces of the spacer. Install four bolts, the washers, and the spacers. Tighten the four bolts to a torque of 50 5 N m (37 4 lb ft).
Apply 5P-3931 Anti-Seize Compound to the threads of bolts (8), the mating surfaces of the bolts, and the mating surfaces of the locknuts.
Install four bolts (8) and the locknuts.
Install two exhaust manifold sleeves (5) and exhaust seal (6) on exhaust manifold (7) .
Position exhaust manifold (2) and gasket (3) for installation.
Illustration 6 g00616730
Apply 5P-3931 Anti-Seize Compound to the threads of bolts (1), the mating surfaces of the bolts, and the mating surfaces of the locknuts.
Install four bolts (1) and the locknuts.
Apply 5P-3931 Anti-Seize Compound to the threads of bolts (4), and the faces of the spacers. Install four bolts, the washers, and the spacers that fasten exhaust manifold (2) and gasket (3) (not shown) to the cylinder head. Tighten the four bolts to a torque of 50 5 N m (37 4 lb ft).Note: Repeat this procedure for the remaining sections of the exhaust manifold. If necessary, install the turbochargers. Refer to Disassembly and Assembly, "Turbochargers - Install" for the correct procedure.End By:
Separate the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".
Remove the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
Install the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
Connect the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".Note: Install caps and plugs on all openings in order to prevent dirt or debris from entering the system. Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal components.Note: The following procedure outlines the removal of two sections of the exhaust manifolds. The same procedure can also be used for the removal of the remaining sections of the exhaust manifolds.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Illustration 1 g00616730
Apply 1U-8265 Penetrating Oil to the threads of four bolts (1). Then apply 4C-5593 Anti-Seize Compound to the threads of four bolts (1) .
Remove four bolts (1) and the locknuts.
Remove bolts (4), the washers, and the spacers that fasten exhaust manifold (2) and gasket (3) (not shown) to the cylinder head.
Illustration 2 g00610004
Illustration 3 g00616729
Remove exhaust manifold (2) and gasket (3) .
Remove two exhaust manifold sleeves (5) and exhaust seal (6) .
If necessary, apply 1U-8265 Penetrating Oil to the threads of four bolts (8). Then apply 4C-5593 Anti-Seize Compound to the threads of four bolts (8) .
Remove four bolts (8) and the locknuts.
Remove bolts (9) (not shown), the washers, and the spacers that fasten exhaust manifold (7) and the gasket to the cylinder head.Note: Repeat this procedure for the remaining sections of the exhaust manifold. If necessary, remove the turbochargers. Refer to Disassembly and Assembly, "Turbochargers - Remove" for the correct procedure.Installation Procedure
Note: Verify that all of the components of the exhaust manifold are clean and free of foreign material prior to installation.Note: The following procedure outlines the installation of two sections of the exhaust manifolds. The same procedure can also be used for the installation of the remaining sections of the exhaust manifolds.Note: Replace all of the high temperature nuts, bolts, and gaskets with new parts.
Illustration 4 g00616729
Illustration 5 g00610004
Position exhaust manifold (7) and the gasket for installation.
Apply 5P-3931 Anti-Seize Compound to the threads of bolts (9) (not shown), and the faces of the spacer. Install four bolts, the washers, and the spacers. Tighten the four bolts to a torque of 50 5 N m (37 4 lb ft).
Apply 5P-3931 Anti-Seize Compound to the threads of bolts (8), the mating surfaces of the bolts, and the mating surfaces of the locknuts.
Install four bolts (8) and the locknuts.
Install two exhaust manifold sleeves (5) and exhaust seal (6) on exhaust manifold (7) .
Position exhaust manifold (2) and gasket (3) for installation.
Illustration 6 g00616730
Apply 5P-3931 Anti-Seize Compound to the threads of bolts (1), the mating surfaces of the bolts, and the mating surfaces of the locknuts.
Install four bolts (1) and the locknuts.
Apply 5P-3931 Anti-Seize Compound to the threads of bolts (4), and the faces of the spacers. Install four bolts, the washers, and the spacers that fasten exhaust manifold (2) and gasket (3) (not shown) to the cylinder head. Tighten the four bolts to a torque of 50 5 N m (37 4 lb ft).Note: Repeat this procedure for the remaining sections of the exhaust manifold. If necessary, install the turbochargers. Refer to Disassembly and Assembly, "Turbochargers - Install" for the correct procedure.End By:
Separate the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".
Remove the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
Parts hose Mercruiser:
866331
866331 HOSE, Cut to 2.75 Inches
40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 424106LUS, 424106PUU
806173 82
806173 82 HOSE, (58.00 Inches Bulk)
40500006T, 40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 424106LTT, 424106LUS, 424106PUU, 4M4102LTS, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
863489
863489 HOSE, Power Steering Cooler To Check Valve
40430002S, 40500006T, 40500010T, 40500010U, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS
863611
863611 HOSE, Sea Pump To Power Steering Cooler
40430002S, 40500006T, 40500010T, 40500010U, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS
864579
864579 HOSE, Check Valve To Thermo Housing
40430002S, 40500006T, 40500010T, 40500010U, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS
863623
863623 HOSE, Check Valve to Fuel Cooler
40500006T, 40500010T, 40500010U, 40500120U, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS
864953
864953 HOSE, Heat Exchanger to Port Elbow
40500006T, 40500010T, 40500010U, 444236HRS, 4M4102LRS, 4M4102LTS
864966
864966 HOSE, Tee Fitting to Starboard Elbow
40500006T, 40500010T, 40500010U, 444236HRS, 4M4102LRS, 4M4102LTS