883971 Mercruiser HOSE-POWER STEERING PUMP TO RESERVOIR


883971 HOSE-POWER STEERING PUMP TO RESERVOIR Mercruiser 40280001D, 428B116KD, 442B115KD, 4A72040ND, 4C72040TD, 4CJ2040ND HOSE
883971 HOSE-POWER STEERING PUMP TO RESERVOIR Mercruiser
Rating:
38

Buy HOSE-POWER STEERING PUMP TO RESERVOIR 883971 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Mercruiser entire parts catalog list:

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1 Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Use Tooling (A) to turn the flywheel in order to access the connecting rod cap that will be removed.
Illustration 1 g00913801Note: Inspect the connecting rod and connecting rod cap for the proper identification mark. The connecting rod and the connecting rod cap should have an etched number on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary.
Remove bolts (1) and connecting rod cap (2) from the crankshaft.
Push the connecting rod away from the crankshaft. Remove the upper half of the connecting rod bearing.Note: Be careful not to damage the cylinder liner or the crankshaft journal.
Remove the lower half of the connecting rod bearing from connecting rod cap (2).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B Loctite Moly 50 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.
Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center.
Illustration 2 g00913801
Illustration 3 g03746219
Section view of connecting rod showing torque sequence. Chamfer (3) and dowel (4) can be used to reference orientation.
Install the upper half of the connecting rod bearing on the connecting rod . Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod. Coat the connecting rod bearing with clean engine oil. Position the connecting rod onto a journal of the crankshaft.
Install the lower half of the connecting rod bearing on connecting rod cap (2). Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod cap. Coat the connecting rod bearing with clean engine oil.Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod. Install the chamfered side of the connecting rod cap next to the thrust surface of the crankshaft.
Apply Tooling (B) to the threads, the shank, and the seat of bolts (1).
Place connecting rod cap (2) into position. Install bolts (1). Use the following procedure to tighten the bolts:
Tighten Bolt (A) and Bolt (B) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolt (C) and Bolt (D) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolt (C) and Bolt (D) again to a torque of 90 5 N m (65 4 lb ft).
Place an index mark on the bolts and the connecting rod cap. Tighten each bolt for an additional 90 5 degrees (1/4 turn).
Rotate the crankshaft in order to ensure that the crankshaft turns freely.End By:
Install the engine oil pump.


Parts hose Mercruiser:

19409 71
 
19409 71 HOSE, (54.00 Inches Bulk)
40200002D, 40200002G, 40420001D, 40500006T, 40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 424106LU
19833 89
 
19833 89 HOSE
40420001D, 40500006T, 40500010T, 40500010U, 40500120U, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND, 4M4102LTS
813289
 
813289 HOSE
428B116KD, 442B110GD, 442B115KD, 4A72040ND
891889
 
891889 HOSE
40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C8204DLD
854188
 
854188 HOSE-BREATHER
40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C8204DLD
896332105
 
896332105 HOSE
40280001D
17435 65
 
17435 65 HOSE, (38.00 Inches Bulk)
40420001D, 4C72040TD, 4C8204DLD, 4CJ2040ND
Back to top