889874 Mercruiser HOSE


889874 HOSE Mercruiser 4C72040TD, 4CJ2040ND HOSE
889874 HOSE Mercruiser
Rating:
93

Buy HOSE 889874 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Compatible models:

4C72040TD   4CJ2040ND   Mercruiser

Mercruiser entire parts catalog list:

4C72040TD 1998
4CJ2040ND 1998

Information:


Illustration 1 g00933179
Typical modules (if applicable)Test Step 1. Check for Connector Damage
Turn the keyswitch to the OFF position.
Thoroughly inspect the ECM connector J1/P1 and the machine connector J2/P2. Inspect all of the other connectors. Refer to the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque of 2.25 0.25 N m (20 2 lb in).
Check the customer connector (allen head screw) for the proper torque of 2.25 0.25 N m (20 2 lb in).
Check the harness and the wiring for abrasion and for pinch points.Expected Result:The connectors and wiring are free of the following problems: damage, corrosion, abrasion and incorrect attachment.Results:
OK - The connectors and wiring are free of any problems. Proceed to Test Step 2.
Not OK - The connectors and/or wiring need repair.Repair: Repair the connectors or wiring and/or replace the connectors or wiring.STOPTest Step 2. Check Communications over the Cat Data Link.
Turn the keyswitch to the OFF position.
Connect the Cat ET to the service tool connector J31.
Turn the keyswitch to the ON position.
Monitor engine operating conditions on the Cat ET. Verify that communications are established between the Cat ET and the engine ECM.Expected Result:Cat ET is able to establish communications with the engine ECM over the Cat Data Link.Results:
OK - Cat ET was able to communicate with the engine ECM over the Cat Data Link.Repair: Verify that Cat ET can communicate with the other modules in the system.STOP
Not OK - Cat ET was not able to establish communications with the engine ECM over the Cat Data Link. Proceed to Test Step 3.Test Step 3. Check the Voltage at the Service Tool Connector.
Disconnect Cat ET.
Measure the voltage between pin A and pin B on the service tool connector J30.Expected Result:The voltage measures 24 3 VDC between the pins. The voltage at the service tool connector provides power for the communication adapter.Results:
OK - The voltage measures 24 3 VDC between the pins. Proceed to Test Step 4.
Not OK - The voltage does not measure 24 3 VDC between the pins.Repair: Check the circuit that is providing power to the service tool connector. Refer to Illustration 1 for the correct pin numbers.STOPTest Step 4. Check for Shorts in the Harness
Turn the keyswitch to the OFF position.
Disconnect ECM connector J1/P1 at the engine ECM.
Disconnect all control modules from the Cat Data Link.
Disconnect Cat ET from the service tool connector J31.
Measure the resistance from P1-33 to P1-19.
Measure the resistance from P1-19 to the chassis ground.
Measure the resistance from P1-33 to the chassis ground.Expected Result:The resistance is greater than 20,000 Ohms for each measurement.Results:
OK - The resistance is greater than 20,000 Ohms for each measurement. Proceed to Test Step 5.
Not OK - The resistance is less than 20,000 Ohms for one or more measurements. There is a short circuit in the harness or in the connectors.Repair: Repair the connectors or wiring and/or replace the connectors or wiring.STOPTest Step 5. Check the Resistance through the Harness.
Use a suitable piece of wire to create a short circuit at the cab service tool connector J31. Short J31-D and J31-E together.
Measure the resistance at the engine's ECM connector P1 between P1-19 and P1-33.
Measure the resistance at the connectors of the other control modules. Refer to Illustration 1 for the correct pin numbers.Expected Result:The resistance is less than 5 Ohms for each measurement.Results:
OK - The resistance is less than 5 Ohms for each measurement. The Cat Data Link does not have an open in the wiring.Repair: If the problem is intermittent, perform the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors".STOP
Not OK - The resistance is greater than 5 Ohms for one or more of the measurements. There is an open circuit in the harness or in the connectors.Repair: Repair the connectors or wiring and/or replace the connectors or wiring.STOP


Parts hose Mercruiser:

19409 71
 
19409 71 HOSE, (54.00 Inches Bulk)
40200002D, 40200002G, 40420001D, 40500006T, 40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 424106LU
19833 89
 
19833 89 HOSE
40420001D, 40500006T, 40500010T, 40500010U, 40500120U, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND, 4M4102LTS
805740
 
805740 HOSE
40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND
883967
 
883967 HOSE-RESERVOIR TO COOLER
40280002D, 428B116KD, 442B115KD, 4A72040ND, 4C72040TD, 4CJ2040ND
883969
 
883969 HOSE (COOLER TO STEERING CCYLINDER)
40280001D, 428B116KD, 442B115KD, 4A72040ND, 4CJ2040ND
865390068
 
865390068 HOSE, Return, Power Steering Cylinder to Cooler
40280001D, 4C72040TD, 4V71222PD, 4V71222TD
866690
 
866690 HOSE, Pressure, Power Steering Pump to Steering Cylinder
40280001D, 4C72040TD, 4V71222PD, 4V71222TD
811464
 
811464 HOSE
40280001D, 40280002D, 40420002D, 4C72040TD, 4CJ2040ND
Back to top