8M0007671 Mercruiser HOSE


8M0007671 HOSE Mercruiser 5P4AB04HH HOSE
8M0007671 HOSE Mercruiser
Rating:
28

Buy HOSE 8M0007671 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

Compatible models:

5P4AB04HH   Mercruiser

Mercruiser entire parts catalog list:

5P4AB04HH 2007,2008

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-4030 Thread Lock Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the turbocharger is clean and free from damage. Inspect the turbocharger for wear. Refer to Systems Operation, Testing and Adjusting, "Turbocharger - Inspect" for more information. If the turbocharger is worn, the complete turbocharger must be replaced.
Illustration 1 g01264131
Typical example
Test actuator (6) for correct operation. Refer to Systems Operation, Testing and Adjusting, "Turbocharger - Inspect". If the actuator is damaged or the actuator does not operate within the specified limits, the complete turbocharger must be replaced.
Clean the gasket surfaces of the exhaust manifold. If necessary, install the studs to the exhaust manifold. Tighten the studs to a torque of 18 N m (13 lb ft).
Install a new gasket (7) to the exhaust manifold.
Position turbocharger (5) onto the exhaust manifold and install nuts (8). Tighten the nuts to a torque of 44 N m (32 lb ft). Note: Do not use the actuator rod to lift the turbocharger.
Position a new gasket (11) and tube assembly (13) onto turbocharger (5). Install bolts (12) finger tight.
Position a new gasket (15) onto the cylinder block. Install bolts (14) finger tight.
Tighten bolts (12) to a torque of 9 N m (80 lb in). Tighten bolts (14) to a torque of 22 N m (16 lb ft).
Lubricate the bearings of turbocharger (5) with clean engine oil through the oil inlet port. Rotate the shaft of the turbocharger in order to distribute the lubricant.
Position tube assembly (3) onto turbocharger (5). Install new washers (2) and banjo bolt (1) to tube assembly (3). Tighten the banjo bolt finger tight.
Install new washers (2) and banjo bolt (4) onto tube assembly (3). Connect the tube assembly to the cylinder block. Tighten the banjo bolt finger tight.
Tighten banjo bolts (1) and (4) to a torque of 18 N m (13 lb ft). Note: Ensure that the tube assembly does not come into contact with any other engine components.
Connect the hose to actuator (6). If necessary, secure tube assembly (3) to the tube assembly for actuator (6). Tube assembly (3) is secured to the tube assembly for the actuator by clips.
If the turbocharger has an exhaust elbow, install the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install".
If the turbocharger has an adapter (9), position the adapter onto the turbocharger. Tighten three nuts (10) progressively. Tighten the nuts to a torque of 25 N m (18 lb ft). Note: Ensure that the adapter is square with the face of the turbocharger.
Connect the air outlet hose to turbocharger (5). If the engine has an air pipe, install the air pipe and install the gasket to the cylinder head. Apply Tooling (A) to the bolts for the air pipe. Tighten the bolts to a torque of 22 N m (16 lb ft).Tighten the hose clamps to a torque of 5 N m (44 lb in).Note: If the air outlet hose has a reflective heat shield, ensure that the reflective heat shield is installed toward the engine.
Connect the air inlet hose to turbocharger (5).


Parts hose Mercruiser:

8M0007711
 
8M0007711 HOSE
5P4AB04HH, 5P4AB04IH
8M0025147
 
8M0025147 HOSE
5P4AB04HH, 5P4AB04IH
8M0007674
 
8M0007674 HOSE
5P4AB04HH
8M0007672
 
8M0007672 HOSE
5P4AB04HH
8M0007670
 
8M0007670 HOSE
5P4AB04HH
8M0007669
 
8M0007669 HOSE
5P4AB04HH, 5P4AZ54JH
8M0007668
 
8M0007668 HOSE
5P4AB04HH, 5P4AB04IH
8M0021789
 
8M0021789 HOSE
5P4AB04HH, 5P4AB04IH
Back to top