8M2006304 Mercruiser HOSE


8M2006304 HOSE Mercruiser 4S42028UU, 4S420P8UE HOSE
8M2006304 HOSE Mercruiser
Rating:
53

Buy HOSE 8M2006304 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

4S42028UU   4S420P8UE   Mercruiser

Information:

Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps Values Results
1. Active Codes and Logged Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM). Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the "Product Status Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
Troubleshoot any active codes before continuing with this procedure.
Codes
Result: There are active codes.
Troubleshoot any active codes before continuing with this procedure.
Result: There are no active codes.
Proceed to Test Step 2.
2. Restriction in the Air Inlet and Exhaust System
A. Check the air filter restriction indicator, if equipped. Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.
B. Check the air inlet and exhaust system for restrictions and/or leaks.
Restrictions
Result: There are restrictions in the air inlet or exhaust system.
Make the necessary repairs, Verify that the repair eliminated the problem.
Result: There are no restrictions in the air inlet or exhaust system.
Proceed to Test Step 4.
3. Check the Fuel System
Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information.
A. Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only.
B. Ensure that the vent in the fuel cap is not filled with debris.
C. Inspect the fuel system for external leaks.
D. Check that there are no external leaks, no air in the clear primary fuel filter. Change the primary fuel filter and the in-line filter for the fuel transfer pump.
E. Check fuel quality. Refer to Systems Operation/Testing and Adjusting, "Fuel Quality - Test" for the proper procedure. Check the fuel tank for debris or foreign objects which may block the fuel supply.
F. Check for the proper operation of the fuel transfer pump. Replace the pre-filter if excessive contamination or if the maintenance interval is exceeded. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for test information.
Fuel system
Result: The fuel system is OK.
Proceed to Test Step 6.
Result: The fuel system is not OK.
Make the necessary repairs.
4. Proper Operation of the Turbocharger
A. Check for proper operation of the turbocharger.
Turbocharger
Result: The turbocharger is operating properly.
Proceed to Test Step 5.
Result: The turbocharger is not operating properly.
Repair or replace the turbocharger. Verify that the repair eliminated the problem.
5. Fuel Injectors
A. If service has been performed on the engine fuel system recently, verify that the injector trim codes in the Engine ECM match the injector for each cylinder. If injectors were moved between cylinders or if an injector was replaced and the injector trim codes were not updated in the Engine ECM, this can cause an engine miss.
A. Access the "Cylinder Cutout Test" in the "Diagnostic Tests" under the "Diagnostics" menu. Cut out each cylinder one at a time to listen for improvements in the engine. If engine sound improves while cutting out a specific cylinder or cylinders, then check that the injector(s) are working properly by using 440-6907 Injector Kit.
Note: The injector deliver quantity is not a reliable indicator of a failed injector. It is not recommended to use that test in determining if an injector is failed.
Fuel Injectors
Result: If injector(s) trim codes for each cylinder do not match what is in the Engine ECM, then refer to Special Instruction, REHS9707 for the procedure to install the new injector QR codes within the Engine ECM and on-line. Confirm that this resolves the issue.
Result: If injector(s) are found to be defective, then replace the injector(s). Refer to Disassembly and Assembly, Electronic Unit Injector - Remove and Install. Refer to Special Instruction, REHS9707 for the procedure to install the new injector QR codes within the Engine ECM and online. Confirm that this resolves the issue. Note: If two or more injectors are not working properly, this is likely a result of water in the fuel, bad fuel, or contaminated fuel. Contaminated fuel can occur by pre-filling the fuel filter or contamination during a previous repair of the fuel system. The root cause needsto be determinedto prevent a repeat occurrence.
Result: There are no previous known services on fuel system and there was no noticeable improvement during the cylinder cut out test. The customer could have ordered injectors through parts and did not change the injector trim codes in the Engine ECM. Visually confirm that the injector trim code for each cylinder matches what is in the Engine ECM. Refer to Special Instruction, REHS9707 for the procedure to install the new injector QR codes within the Engine ECM and on-line.
6. Machine Hydraulics Causing Excessive Load
Refer to the machine System Operation/Testing and Adjustmanual to ensure that machine hydraulics are working properly.
Machine Hydraulics
Result: Machine hydraulics are causing an excessive load.
Make the necessary repairs.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts hose Mercruiser:

19409 71
 
19409 71 HOSE, (54.00 Inches Bulk)
40200002D, 40200002G, 40420001D, 40500006T, 40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 424106LU
863056 1
 
863056 1 HOSE, (42.00 Inches Bulk) Black, Air
40430002S, 40500006T, 40500010T, 40500010U, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
863095
 
863095 HOSE, Elbow to Manifold
4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU
864488
 
864488 HOSE, Heat Exchanger to Water Rail
4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
863900
HOSE, Oil, Filter to Cooler
863900 HOSE, Oil, Filter to Cooler
4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU
8M2012143
 
8M2012143 HOSE, Inlet to Reservoir
4S42028UU, 4S420P8UE
8M2007279
8M2012906
Back to top