96246A 4 Mercruiser HOSE, FLUID COOLER TO HOUSING (3/4" I.D.)


96246A 4 HOSE, FLUID COOLER TO HOUSING (3/4" I.D.) Mercruiser 00014332, 02287333, 02602347, 02607333, 02608427, 04544347, 06661346, 07711346, 08987343, 30001854, 32001876, 457B101JS, 457B111GS HOSE

Buy HOSE, FLUID COOLER TO HOUSING (3/4" I.D.) 96246A 4 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

Mercruiser entire parts catalog list:

00014332 1982
02287333 1983
02602347 1987,1988,1989,1990,1991,1992,1993,1994,1995
02607333 1983
02608427 1987
04544347 1987
06661346 1986,1987,1988,1989
07711346 1986,1987
08987343 1983,1984,1985,1986,1987
30001854 1984,1986
32001876 1986,1987
457B101JS 1996
457B111GS 1994,1995

Information:

Starting the Engine
Refer to the Owner's Manual of the OEM for your type of controls. Use the following procedure to start the engine.
Place the transmission in NEUTRAL. Disengage the flywheel clutch to allow the engine to start faster, and to reduce the draining of the battery.
Turn the ignition switch to the ON position.During the key on, the diagnostic lamp, and warning lamp will be checked for proper bulb operation. If any of the lamps do not illuminate, replace the bulb.
Do not engage the starting motor when flywheel is turning. Do not start the engine under load.If the engine fails to start within 30 seconds, release the starter switch or button and wait two minutes to allow the starting motor to cool before attempting to start the engine again.
Push the start button or turn the ignition switch to the START position to crank the engine.Do not push down or hold the throttle down while the engine is cranked. The system will automatically provide the correct amount of fuel that is needed to start the engine.
If the engine fails to start within 30 seconds, release the start button, or the ignition switch. Wait for 2 minutes to allow the starting motor to cool before attempting to start the engine again.
Oil pressure should rise within 15 seconds after the engine starts. Do not increase engine rpm until the oil pressure gauge indicates normal. If oil pressure is not indicated on the gauge within 15 seconds, DO NOT operate the engine. STOP the engine, investigate and correct the cause.
Allow the engine to idle for approximately 3 minutes. Idle the engine until the water temperature gauge has begun to rise. Check all gauges during the warmup period.Note: Oil pressures and fuel pressures should be in the normal range on the instrument panel. Engines that are equipped with "" lamps do not have an operating range. The " and DIAGNOSTIC" lamp (if equipped) will flash while the engine is cranking. The lamp should turn off after proper engine oil pressure or fuel pressure is achieved. Do not apply a load to the engine or increase engine rpm until the oil pressure gauge indicates at least normal pressure. Inspect the engine for leaks and/or unusual noises.If the engine is operated with a low load, the engine will reach normal operating temperature sooner than idling the engine with no load. When the engine is idled in cold weather, increase the engine rpm to approximately 1000 to 1200 rpm to warm up the engine more quickly. Do not exceed the recommended rpm to increase the speed of the warmup. Limit unnecessary idle time to 10 minutes.Starting Problems
An occasional starting problem may be caused by one of the following items:
Low battery charge
Lack of fuel
Problem with the wiring harnessIf the engine fuel system has been run dry, fill the fuel tank and prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System - Prime" topic (Maintenance Section).If the other problems are suspected, perform the appropriate procedure to start the engine.Problems with the Wiring Harness
Illustration 1 g01248812
ECM Connector J2/P2
Locate the ECM. Check the connector to ensure that the connector is secure. Lightly pull each of the wires in the chassis harness.
Pull each wire with approximately 4.5 kg (10 lb) of force. The wire should remain in the connector.
If a wire is loose, push the wire back into the connector. Pull the wire again to ensure that the wire is secure.
Start the engine. If the engine does not start, consult the nearest Caterpillar dealer for assistance.


Parts hose Mercruiser:

32461
 
32461 HOSE, WATER - BELL HOUSING TO GIMBAL HOUSING (13 3/4")
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 5000165CE
93315 12
 
93315 12 HOSE, VENT-CARBURTOR (10")
00014332, 01207333, 01402414, 01407333, 01701335, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 04708004, 04856332, 04881333, 06661346, 07711346, 08986342,
79672
 
79672 HOSE, THERMOSTAT HSG. TO REAR CAP (STARBOARD)
02607333, 03302336, 03307332, 260801
47516 11
53461 70
 
53461 70 HOSE, (48.00 Inches Bulk), WATER PUMP TO OIL COOLER (7")
03307332, 03308333, 04544347, 37011856, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910TP, 5E31910TS, 5E32200TP, 5E32900TS, 5E36200TP, 5E36200TS, 5E36210TP, 5E36210TS, 5
88794
 
88794 HOSE, THERMOSTAT HOUSING TO FLUID COOLER
00014332, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 07711346, 08987343, 30001854, 32001876
66285 4
 
66285 4 HOSE
32001876
87117 1
 
87117 1 HOSE (STARBOARD)
02602347, 02608427, 443B1003S
Back to top