98549 Mercruiser HOSE, OIL COOLER TO OIL COOLER

Safety Section
Do not perform any procedure in this Special Instruction until you have read Special Instruction and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in personal injury. The following procedures should also be observed.Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. The installer must be alert to potential hazards and have the necessary training, skills, and tools needed to perform these functions properly. Wear safety equipment, such as eye protection, foot protection, and other protection as is appropriate to the work site.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive. Ensure that any tool, procedure, work method, or operating technique you use that is not recommended by Caterpillar is safe. Ensure that the product will not be damaged or the product will be made unsafe by the operation, lubrication, maintenance, or the repair procedures that are used.
Personal injury or death can result from improper assembly procedures.Do not attempt any assembly until you have read and understand the assembly instructions.
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Prepare the Machine
If the machine is portable, then move the machine to a smooth, level surface that will support the weight of the machine.
Turn off the machine with the engine switch to the OFF position.
Use proper Lock out and Tag out procedures. Attach a "Do Not Operate" warning tag to the machine start switch or the controls before you perform any service to the machine. These warning tags Special Instruction, SEHS7332 are available from your Caterpillar dealer.Overview
Applicability
The Natural Gas Flow Meter is offered as an aftermarket attachment for use on all Natural Gas and Dynamically Blended Gas engines, both Caterpillar and competitive brands, providing a fleet solution for equipment owners.Electrical Requirements
This control is designed to operate on 12 or 24 volts DC, negative ground. Current draw of the control package is less than 2.0 amps. External solenoids or other loads driven by the control and connection of a Caterpillar Electronic Technician (ET) communications adapter will add to the current draw.Remote Monitoring Requirements
Remote monitoring requires that a telematics system, such as Product Link, be installed on the machine or equipment to transmit the data off board. The Natural Gas Flow Meter kit does not include any required hardware to install a data monitoring and recording device.Features
A new kit will require configuring parameters in the already programmed ECM.The Natural Gas Flow Meter sends information back to the AssetIQ ECM to be transmitted onto the machine telematics and will transmit this data, along with diagnostic information, on the main J1939 data link, and the main CDL data link to be received by a recording ECM such as Product Link.
Illustration 1 g06226871When connected, Cat ET will display.Required Parts
Natural Gas Flow Meter Kit Supplied Parts for Installation
Note: Listed below are the contents of the bill of materials for 464-7821 Display Module Group, at the time of publication of this document.
Table 1
Contents of the 464-7821 Display Module Group (Natural Gas Flow Meter)
Qty Part Number Part Name
50 3S-2093 Cable Strap
4 9X-3402 Connector Socket
1 470-9410 Flow Meter Group
1 484-2010 Harness Assembly
Illustration 2 g06226877
470-9410 Flow Meter Group
Illustration 3 g06226878
484-2010 Harness Assembly
Additional Parts Needed for Installation
AssetIQ System (Engine) Kit Supplied Parts for Installation
Note: Listed below are the contents of the bill of mate