59362A 1 Mercruiser IMPELLER ASSEMBLY


59362A 1 IMPELLER ASSEMBLY Mercruiser 02287333, 02607333, 03302336, 03307332, 04706002, 04707333, 08986342, 228801, 260801 IMPELLER
59362A 1 IMPELLER ASSEMBLY Mercruiser
Rating:
88

Buy IMPELLER ASSEMBLY 59362A 1 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$40.99

02-04-2025
0.4375[0.20] pounds
CN: Shanghaisalingschuan
SLSRPMT Water Pump Impeller Kits 59362T6 for Mercury MerCruiser Bravo 1 2 3 Inboard Engines 4.3L 5.0L 5.7L 7.4L V8 Sterndrive Replace 47-59362T 6 59362Q01 Sierra 18-3087
SLSRPMT Fits for Mercruiser Inboard Gas Engines 5.7L 350 CID V8 GM 5.7L COMPETITION SKI GEN+ 0L002005 THRU 0M316999 boat motor parts cooling system. || Replaced by MerCruiser Engines with One Piece Pump Body is replaced by 47-59362T1, 47-59362T 1, 59362T1, 59362T 1, 47-593621, 47-59362 1, 47-59362-1, 593621, 59362 1, 59362-1, 47-59362, 59362, 47-59362A1, 47-59362A 1, 59362A1, 59362A 1, 47-59362Q01 Sierra 18-3087,Compatibale with the outboards Sierra Marine 18-3224 GLM 12084. || It is very important to check your boat motor part number before purchase. please message us s/n, year and horsepower if you are not sure. || Package Included: impeller x 1, plate x 1, o-ring x 1 and RING-QUARD x 1 as pictures showed. || VERY IMPORTANT- Same horsepower and year, different model, It may have a totally difference. Please check your outboard model, serial number and year before purchase. You can ask us questions if you are not sure, we're pleasure to help you.
$20.00

01-01-2025
0.2358[0.11] pounds
CN: Tcess
Tcess Compatible with Sierra 18-3087, Mercury 47-59362T1 Water Pump Impeller For Mercruiser Bravo I II & III 47-59362
Generic 💡Replaces part # 47-59362T1, 47-59362T 1, 59362T1, 59362T 1, 47-593621, 47-59362 1, 47-59362-1, 593621, 59362 1, 59362-1, 47-59362, 59362, 47-59362A1, 47-59362A 1, 59362A1, 59362A 1, 47-59362Q01 Sierra 18-3087. || 💡For Mercruiser Inboard Gas Engines 5.7L 350 CID V8 GM 5.7L COMPETITION SKI GEN+ 0L002005 THRU 0M316999 boat motor parts cooling system. || 💡The kit included everything shown above. || 💡 See your owner's manual or service manual for specific applications and replacement instructions. || 💡We will show more detailed information about the product on the details page below to ensure that we can help you to buy the correct replacement part.
$14.45
 

17-01-2023

-: -
47-59362T1 18-3087 Sea Water Pump Impeller For Mercury Mercruiser Sierra Inboard/Sterndrive Gas Engines Bravo I II & III 4.3/5.0/5.7/7.4/8.2/9.0/9.1 L V6 V8 59362Q01 593621 59362A1 59362B1 17954-0001P
????️■OEM#■:Replacing part numbers For Mercury Mercruiser 47-59362T1 59362Q01 59362 593621 59362A1 Sierra 18-3087 Jabsco 17954-0001PMallory 9-45375,perfectly match. || ????️■High Quality■:Original level of quality and durability, the impellers are manufactured from high quality rubber and will not be damaged even after long periods of immersion in salt water. || ????️■Buy With Confidence■:Highly rigid cardboard boxes and foam wool packaging ensure that your order is in mint condition before you receive it. || ????️■Inquiry Service■:Check your engine part number before you buy. If you're not sure, send us a message. We'll help you find the right part number for your engine. || ????️■Tips■:We will show more detailed information about the product on the details page below to ensure that we can help you to buy the correct replacement part.
Number on catalog scheme: 10
 

Mercruiser entire parts catalog list:

02287333 1983
02607333 1983
03302336 1986
03307332 1982
04706002 1982,1983
04707333 1983
08986342 1982,1983
228801 1981,1982
260801 1981,1982,1987

Information:


Table 1
Diagnostic Trouble Codes for the DEF Pump Pressure Sensor
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
4334-3 3090-3 Aftertreatment 1 Diesel Exhaust Fluid Doser 1 Absolute Pressure : Voltage Above Normal There is excessive voltage on the signal wire between the Electronic Control Module (ECM) and the DEF pump.
or
There is an open circuit on the supply, signal, or return wire.
The code is logged.
4334-4 3090-4 Aftertreatment 1 Diesel Exhaust Fluid Doser 1 Absolute Pressure : Voltage Below Normal There is low voltage on the signal wire between the ECM and the DEF pump pressure sensor.
The code is logged.
Follow the troubleshooting procedure to identify the root cause of the problem.
Illustration 1 g06208827
Illustration 2 g06208829
View of the pin locations for the DEF pump on the P1 ECM connector
(28) DEF pump pressure sensor signal
(46) DEF pump pressure sensor 5 VDC supply
(50) DEF pump pressure sensor return
Illustration 3 g03416460
Pin location on the DEF pump connector
(2) Pressure sensor supply
(3) Pressure sensor signal
(4) Pressure sensor return
Table 2
Required Tools
Tool Part Number Part Description Qty
A 372-5260 Test Kit 1 Complete the procedure in the order in which the steps are listed.
Table 3
Troubleshooting Test Steps Values Results
1. Determine the Diagnostic Code
A. Establish communication between the electronic service tool and the engine Electronic Control Module (ECM). Refer to Troubleshooting, "Electronic Service Tools"
B. Check for active or logged codes.
Diagnostic trouble codes
Result: There is an active or logged 4334-3 (3090-3) or 4334-4(3090-4) diagnostic code.
Proceed to Test Step 2.
2. Inspect Electrical Connectors and Wiring
A. Inspect the P1 ECM connector.
B. Inspect the connector for the DEF pump.
C. Perform a 45 N (10 lb) pull test on each of the wires in the P1 ECM connector and the connector for the DEF pump.
D. Check all the wiring associated with the DEF pump for abrasions and pinch points.
Damaged wire or connector
Result: A damaged wire or damaged connector was not found.
Proceed to Test Step 3.
Result: A damaged wire or damaged connector was found.
Repair: Repair the damaged wire or the damaged connector.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
3. Check for an Open Circuit in the Wiring Harness for the DEF Pump Pressure Sensor Circuit
A. Turn the keyswitch to the OFF position for 2 minutes. The keyswitch must be OFF for 2 minutes to allow the DEF pump to purge, reset the code, and reset the ECM.
B. Disconnect the wiring harness from the DEF pump and the P1 connector on the ECM.
C. Connect Tooling A to the DEF pump connector.
Note: The connector must be used to prevent damage to the DEF pump connector.
D. Measure the resistance between terminal 2 (SUPPLY) on the DEF pump connector and P1:46.
E. Measure the resistance between terminal 3 (SIGNAL) on the DEF pump connector and P1:28.
F. Measure the resistance between terminal 4 (RETURN) on the DEF pump connector and P1:50.
Less than 5.0 Ohms
Result: All resistance measurements are less than 5.0 Ohms.
Proceed to Test Step 4.
Result: At least one of the resistance measurements is greater than 5.0 Ohms. There is an open in the harness.
Repair: Repair the wiring or replace the harness.
Verify that the fault is resolved.
Proceed to Test Step 6.
4. Check for Short Circuits in the Wiring Harness for the DEF Pump Pressure Sensor Circuit
A. Turn the keyswitch to the "OFF" position.
B. Disconnect the wiring harness from the DEF pump and P1 on the ECM.
C. Connect Tooling A to the DEF pump connector.
Note: The connector must be used to prevent damage to the DEF pump connector.
D. Measure the resistance between terminal 2 (SUPPLY) on the DEF pump connector and a known good chassis ground.
E. Measure the resistance between terminal 3 (SIGNAL) on the DEF pump connector and a known good chassis ground.
F. Measure the resistance between terminal 4 (RETURN) on the DEF pump connector and a known good chassis ground.
Greater than 100k Ohms
Result: All resistance measurements are greater than 100k Ohms.
Proceed to Test Step 5.
Result: At least one of the resistance measurements is less than 100k Ohms. There is a short circuit in the harness.
Repair: Repair the wiring or replace the harness.
Verify that the fault is resolved.
Proceed to Test Step 6.
5. Check for Short Circuits Between the DEF Pump Pressure Sensor and the ECM
A. Turn the keyswitch to the "OFF" position.
B. Disconnect the wiring harness from the DEF pump and P1 on the ECM.
D. Measure the resistance between P1:46 and all other pins in the P1 connector.
E. Measure the resistance between P1:28 and all other pins in the P1 connector.
F. Measure the resistance between P1:50 and all other pins in the P1 connector.
Greater than 100k Ohms
Result: All the resistance measurements are greater than 100k Ohms. A failed DEF pump has been detected.
Repair: Replace the DEF pump.
Proceed to Test Step 6.
Result: At least one of the resistance measurements is less than 100k Ohms. There is a short circuit in the harness.
Repair: Repair the wiring or replace the harness.
Verify that the fault is resolved.
Proceed to Test Step 6.
6. Perform a DEF Dosing System Verification Test
A. Turn the keyswitch to the "ON" position. Do not start the engine.
B. Connect the electronic service tool to the diagnostic connector.
C. Perform the "DEF Dosing System Verification Test" .
Diagnostic codes
Result: The code did not return.
Return the unit to service.
Result: The code returned.
Contact the Dealer Solutions Network (DSN).


Parts impeller Mercruiser:

86462
 
86462 IMPELLER, WATER PUMP
04706002, 04707333, 04856332
59362
 
59362 IMPELLER
00014332, 02287333, 02297343, 02607333, 02608427, 03307332, 03308333, 04544347, 08987343, 30001854, 37011856, 44031854, 474H110AR
86462A 1
 
86462A 1 IMPELLER, WATER PUMP
01701335, 04707333, 04708004, 04881333
Back to top