801331642 Mercruiser KEY


801331642 KEY Mercruiser 40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND KEY
801331642 KEY Mercruiser
Rating:
38

Buy KEY 801331642 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Mercruiser entire parts catalog list:

40280001D 1998
40420001D 1998
428B116KD 1997,1998
442B110GD 1994,1995,1996,1998
442B115KD 1997
4A72040ND 1998
4C72040TD 1998
4C8204DLD 1998
4CJ2040ND 1998

Information:


Typical Example1. Remove bolts (1), and pull governor drive (2) from the front drive housing.
Typical Example2. Make sure the O-ring seals are in position on the front of governor drive (1), and put clean engine oil on the seals.3. Put governor drive (1) in position, and install bolts (2) to hold it to the front drive housing.End By:a. install governorDisassemble Governor Drive
Start By:a. remove governor drive 1. Remove O-ring seals (1), (2) and (3) from the front of the governor drive housing.2. Remove the bolts that hold adapter (4) in position, and pull adapter (4) from the housing. 3. Remove pinion (5), shims (6), seals (7) and (8) from adapter (4). Measure the thickness of shims (6), and put identification marks on them for assembly purposes. 4. Remove hose assembly (9)(not included on later machines), cover (11) and the gasket from governor drive housing (10). 5. Remove gear (13) and coupling (12) from housing (10) as a unit. 6. Remove ring (14) to remove coupling (12) from gear (13). 7. If necessary, remove bearing (15) from housing (10).Assemble Governor Drive
1. Align the oil hole in the bearing with the drilled oil passage in governor drive housing (1). Use tool group (A), and install the bearing in housing (1) until it is 1.0 0.5 mm (0.40 .02 in.) below the surface of the housing. The inside diameter of the bearing after assembly is 34.072 0.039 mm (1.3414 .0015 in.). 2. Put coupling (3) in position in gear (2), and install ring (4) to hold the gear and coupling as a unit. 3. Install coupling (3) and gear (2) as a unit in housing (1). 4. Install pinion (5) in adapter (6). 5. Put adapter (6) and shims (7) of the original thickness in position, and install the bolts to hold the unit together.6. Make an adjustment of the gear clearance (backlash) between gear (2) and the pinion as follows:a. Install tool group (B) on gear (2) as shown to check the gear clearance (backlash) at four locations around gear (2) 90° apart.b. Hold the pinion in position, and push down while gear (2) is moved back and forth. Make a record of the indications on tool group (B). Use the lowest indication as the correct gear clearance (backlash) value. The correct gear clearance (backlash) is 0.100 + 0.050 or - 0.025 mm (.0039 + .0020 or - .0010 in.).c. Add or subtract shims (7) as necessary until the gear clearance (backlash) is correct.7. Remove tool group (B), the adapter and pinion from the housing. 8. Connect hose assembly (8) (if equipped) to housing (1). Put the gasket and cover (9) in position, and install the bolts and washers to hold them to housing (1). 9. Install seals (10) and (11) on adapter (6), and put clean engine oil on them.10. Install the correct amount of shims (7) and adapter (6) with the pinion in housing (1), and tighten the bolts. 11. If necessary, make a replacement of pins (14). Make sure the pins are 14 1 mm (.55 .04 in.) above the surface of the housing.12. Install O-ring seal (12) and seals (13) on the front of the housing. Put clean engine oil on the seals.End By:a. install governor drive


Parts key Mercruiser:

7034
 
7034 KEY, ROTOR ASSEMBLY SHAFT
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 06661346, 07711346, 08986342, 228801, 260801, 30001854, 32001876, 3701
801331735
 
801331735 KEY
40280001D, 40280002D, 40420001D, 40420002D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
801331705
 
801331705 KEY-PULLEY
442B110GD, 442B115KD
879718
 
879718 KEY-PULLEY
40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C8204DLD
811404
 
811404 KEY
40420001D, 442B110GD, 442B115KD, 4C8204DLD
805678
 
805678 KEY SWITCH
40420001D, 428B116KD, 442B110GD, 442B115KD, 473B116KD, 473B1F0GS, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND, 4V71222ND, 4V71222PD, 4V71222TD
813313
 
813313 KEY
428B116KD, 442B110GD, 442B115KD, 4A72040ND
854136
 
854136 KEY
40280001D, 428B116KD, 442B115KD, 4A72040ND, 4C72040TD, 4CJ2040ND
Back to top