42841A10 Mercruiser LEAD ASSEMBLY, DISTRIBUTOR TO COIL


42841A10 LEAD ASSEMBLY, DISTRIBUTOR TO COIL Mercruiser 00014332, 02287333, 02297343, 02607333, 02608427, 07711346, 08987343, 30001854, 37011856 LEAD
42841A10 LEAD ASSEMBLY, DISTRIBUTOR TO COIL Mercruiser
Rating:
43

Buy LEAD ASSEMBLY, DISTRIBUTOR TO COIL 42841A10 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

Mercruiser entire parts catalog list:

00014332 1982
02287333 1983
02297343 1983,1985,1986
02607333 1983
02608427 1987
07711346 1986,1987
08987343 1983,1984,1985,1986,1987
30001854 1984,1986
37011856 1986,1987

Information:


Turbocharger bearing failures can cause large quantities of oil to enter the air intake and exhaust systems. Loss of engine lubricant can result in serious engine damage.Minor leakage of oil into a turbocharger under extended low idle operation should not cause problems as long as a turbocharger bearing failure has not occured.When a turbocharger bearing failure is accompanied by a significant engine performance loss (exhaust smoke or engine rpm up at no load), do not continue engine operation until the turbocharger is renewed.
A visual inspection of the turbocharger or turbochargers can minimize unscheduled downtime. A visual inspection of the turbocharger or turbochargers can also reduce the chance for potential damage to other engine parts. Do not inspect the engine with the engine in operation.Single Turbocharger
Illustration 1 g02136079
Typical example
Ensure that the turbocharger is clean and free from dirt before removing components for inspection.
Remove the pipe from the turbocharger exhaust outlet and remove the air intake pipe (1). Visually inspect the piping for the presence of oil. Clean the interior of the pipes to prevent dirt from entering during reassembly.
Check for obvious heat discoloration of the turbocharger. Check for any loose bolts or any missing bolts. Check for damage to the oil supply line and the oil drain line. Check for cracks in the housing of the turbocharger. Ensure that the compressor wheel can rotate freely.
Check for the presence of oil. If oil is leaking from the back side of the compressor wheel, there is a possibility of a failed turbocharger oil seal.The presence of oil may be the result of extended engine operation at low idle. The presence of oil may also be the result of a restriction of the line for the intake air (clogged air filters), which causes the turbocharger to slobber.
Install the air intake pipe and the exhaust outlet pipe to the turbocharger housing. Ensure that all clamps are installed correctly and that all clamps are tightened securely. For more information, refer to Systems Operation, Testing, and Adjusting, "Turbocharger - Inspect".Engine Install with High-Pressure and Low-Pressure Turbochargers
Illustration 2 g06464497
Typical example
(1) High-pressure turbocharger
(2) Elbow
(3) Low-pressure turbochargerThe engine is equipped with a high-pressure turbocharger (1) and a low-pressure turbocharger (3). A regular visual inspection of both turbochargers is recommended. If the turbocharger fails during engine operation, damage to the turbocharger compressor wheel and/or to the engine may occur. Damage to the turbocharger compressor wheel can damage the pistons, the valves, and the cylinder head.Inspecting
The compressor housing for the turbocharger must not be removed from the turbocharger for inspection or removed for the cleaning of the compressor.
Ensure that the turbochargers are clean and free from dirt before removing components for inspection.
Remove the pipe from the high-pressure turbocharger exhaust outlet and remove the air intake pipe to the turbocharger. Visually inspect the piping for the presence of oil. Clean the interior of the pipes to prevent dirt from entering during reassembly.
Remove elbow (2) and check for the presence of engine oil.
Check for obvious heat discoloration of the turbocharger. Check for any loose bolts or any missing bolts. Check for damage to the oil supply line and the oil drain line. Check for cracks in the housing of the turbocharger. Ensure that the compressor wheel can rotate freely.
Check for the presence of oil. If oil is leaking from the back side of the compressor wheel, there is a possibility of a failed turbocharger oil seal.The presence of oil may be the result of extended engine operation at low idle. The presence of oil may also be the result of a restriction of the line for the intake air (clogged air filters), which causes the turbocharger to slobber.
Inspect the bore of the housing of the turbine outlet for corrosion.
Install the air intake pipe and the exhaust outlet pipe to the turbocharger housing. Ensure that all clamps are installed correctly and that all clamps are tightened securely. For more information, refer to Systems Operation, Testing, and Adjusting, "Turbocharger - Inspect".


Parts lead Mercruiser:

45551
 
45551 LEAD, Battery (POSITIVE)
00014332, 2140208, 2165208
45552
 
45552 LEAD, Battery (NEGATIVE)
00014332, 2140208, 2165208
65773A 6
 
65773A 6 LEAD ASSEMBLY, PRIMARY TERMINAL
02287333, 02607333, 03302336, 03307332, 08986342, 228801, 260801, 44031854
92151A32
 
92151A32 LEAD ASSEMBLY, DISTRIBUTOR TO COIL (5")
02287333, 02607333, 03302336, 03307332, 08986342, 228801, 260801
92151A36
 
92151A36 LEAD ASSEMBLY, HIGH TENSION
01206002, 01207333, 01326013, 01406002, 01407333, 02287333, 02607333, 03302336, 03307332, 04706002, 04707333, 04856332, 08986342, 228801, 260801
60686
 
60686 LEAD, FIELD FRAME BRUSH
01206002, 01207333, 01326013, 01406002, 01407333, 02287333, 02607333, 03302336, 03307332, 08986342, 228801, 260801
Back to top