809148 Mercruiser LEAD WIRE


809148 LEAD WIRE Mercruiser 40420001D, 4231017L1, 4262C01JT, 428B116KD, 4332087N1, 4350104JS, 4350104KS, 4350111HS, 4350118JS, 4350118KS, 442B110GD, 442B115KD, 4441027LE, 444106AM1, 444106LPS, 4454118JT, 4502111FE, 4542067LS, 457B101JS, 457B101KS, 457B111GS, 457L101JS, 4652027L LEAD
809148 LEAD WIRE Mercruiser
Rating:
8

Buy LEAD WIRE 809148 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$39.95
 

23-07-2024
0.17[0.08] Pounds
US: Race-Driven Inc
Shock Bushings fit Polaris Ranger Diesel 2015-2018 Front by Race-Driven
Race-Driven Race-Driven Poly Shock Bushings || Designed to perfectly fit and replace the weak OEM stock bushings. || Will NOT fit Fox shocks || Fits: 2015 2016 2017 2018 Polaris Ranger Diesel
$65.06
 

22-08-2024
2.0[0.90] Pounds
US: DK Hardware Supply
Kiwkset 809148 Abbey Smartkey Vestibule Lockset, Polished Brass
Kiwkset Kwikset Smartkey Abbey Vestibule Lockset Polished Brass || Kwikset || RCS
Number on catalog scheme: 32
 

Mercruiser entire parts catalog list:

40420001D 1998
4231017L1 1998
4262C01JT 1996,1997
428B116KD 1997,1998
4332087N1 1998
4350104JS 1996
4350104KS 1997
4350111HS 1995
4350118JS 1996
4350118KS 1997
442B110GD 1994,1995,1996,1998
442B115KD 1997
4441027LE 1998
444106AM1 1998
444106LPS 1998
4454118JT 1996,1997
4502111FE 1993,1994,1995,1996
4542067LS 1998
457B101JS 1996
457B101KS 1997
457B111GS 1994,1995
457L101JS 1996
4652027LE 1998
4652027M1 1998
4652227MW 1998
473B1F0GS 1994,1995,1996
474L111JS 1996,1997
474L118JS 1996
474L118JT 1996,1997
4A72040ND 1998
4C72040TD 1998
4C8204DLD 1998
4CJ2040ND 1998
4M31027LS 1998

Information:

1. Install the turbocharger on tool (A) as shown.2. Put alignment marks on the three housings of the turbocharger for correct alignment during assembly. Loosen clamp (2) and remove the clamp and housing (1) from housing assembly (3). 3. Loosen clamp (4) and remove housing assembly (3) from housing (5). 4. Put the cartridge group in position in tool (B) as shown.
When the nut is loosened, do not put a side force on the shaft. This can result in a bent shaft.
5. Use a 5S9566 sliding T-wrench and a universal socket (6) to remove the nut that holds the compressor wheel to the wheel assembly.6. Remove compressor wheel (7) and the shims from wheel assembly (8).7. Remove housing assembly (3) from wheel assembly (8). 8. Remove ring (9) and backplate (10) from wheel assembly (8). 9. Use tool (C), and remove snap ring (11) from housing assembly (3). 10. Remove insert (12) and sleeve (13) from housing assembly (3). 11. Remove ring (14) from sleeve (13). 12. Remove two screws (15) and deflector (16) from housing assembly (3). 13. Remove ring (18) and bearing assembly (17) from the housing assembly. 14. Remove sleeve (19) and ring (20) from the housing assembly. 15. Remove O-ring seal (23) from the housing assembly.16. Use tood (D) and remove snap ring (22) from the housing assembly.17. Remove bearing (21). Remove the snap ring behind the bearing with tool (D). 18. Use tool (D), and remove snap ring (25) from the housing assembly.19. Remove bearing (24). Remove the snap ring behind the bearing with tool (D).20. Check all the parts of the turbocharger for damage. If the parts are damaged, use new parts for replacement. See Special Instruction Form No. SMHS6854 for Turbocharger Reconditioning. Also, see Guidelines for Reuseable Parts, Form No. SEBF8018.Assemble Turbocharger
1. Make sure that all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material. Do not put oil on any parts of the turbocharger until after the compressor wheel has been installed. After the turbocharger has been assembled, put clean engine oil into the oil inlet of the turbocharger.
Make sure that the snap rings that hold bearings (2) and (5) in position in housing assembly (3) are installed with the round edge of the outside diameter toward the bearing.
2. Install the snap ring behind bearing (2) with tool (A).3. Install bearing (2) in housing (3).4. Use tool (A) and install snap ring (1) in the housing assembly. 5. Install the snap ring behind bearing (5) with tool (A).6. Install bearing (5) in the housing assembly.7. Use tool (A) and install snap ring (4) in the housing assembly. 8. Put wheel assembly (8) in position on tool (B) as shown.9. Put backplate (7) in position on the wheel assembly. Put 6V2055 High Vacuum Grease in the groove for seal ring (6) at assembly to one half or more of the depth of the groove all the way around.10. Install ring (6) in the groove in wheel assembly (8). 11. Put housing assembly (3) in position on wheel assembly (8). 12. Install ring (9) and sleeve (10) on the wheel assembly. 13. Make sure screen is in place in bearing assembly (11). 14. Install bearing assembly (11) over the sleeve. Make sure the screen in the bearing assembly is facing down when it is installed.15. Put ring (12) in position on bearing assembly (11). 16. Put deflector (14) in position in the housing assembly and install two screws (13). Put 6V2055 High Vacuum Grease in the groove of sleeve (15) to one half or more of the depth of the grooves all the way around.17. Install ring (16) in the groove in sleeve (15). 18. Put sleeve (15) in position in insert (17). Install the insert and sleeve (15) as an assembly. 19. Use tool (C) and install snap ring (18) to hold insert (17) in place. 20. Put wheel (21) in position in compressor housing (20). Center the wheel in the compressor housing.21. Use a straight edge and a depth micrometer (19) and measure the distance between the wheel seating face and the compressor housing mounting face (dimension X) in four places. Find the average of the measurements. 22. Use a depth micrometer (19) to measure the distance between the face of housing assembly (3) and the surface of sleeve (15) (dimension Y).23. Use a depth micrometer (19) and measure the distance between the surface of housing assembly (3) and the compressor housing mounting face (dimension Z).24. Calculate the necessary shim thickness as follows: The shims must be of uniform thickness and free of burrs and other imperfections. The total shim thickness should be 0.13 mm to 0.41 mm (.005 to .016 in.) and consist of one or two shims.25. Install wheel (21) at room temperature as follows:a. Put the correct amount of shims and wheel (21) in position on the wheel assembly.b. Put a small amount of clean engine oil on the threads of the wheel assembly.
Do not put a side force on the shaft when the nut that holds the compressor wheel in position is tightened.
c. Install the nut that holds wheel (21) in place. Tighten the nut to a torque of 14 to 17 mm (125 to 150 lb. in.).d. Remove the nut and put 6V1541 Quick Cure Primer on the threads of the wheel assembly.e. Put 9S3265 Retaining Compound on the threads of the wheel assembly and install the nut. Tighten the nut to a torque of 4 mm (35 lb. in.).f. Tighten the nut an additional 90°. 26. Install housing (23) on tool (D) as shown.27. Put housing assembly (3)


Parts lead Mercruiser:

809147
 
809147 LEAD WIRE
40420001D, 4231017L1, 4262C01JT, 428B116KD, 4332087N1, 4350104JS, 4350104KS, 4350111HS, 4350118JS, 4350118KS, 442B110GD, 442B115KD, 4441027LE, 444106AM1, 444106LPS, 4454118JT, 4502111FE, 4542067LS, 457B101JS, 457B101KS, 457B111GS, 457L101JS, 4652027L
Back to top