77931 Mercruiser ROD, AUTOMATIC CHOKE (STERN DRIVE)


77931 ROD, AUTOMATIC CHOKE (STERN DRIVE) Mercruiser 02602347, 02608427, 03302336, 03307332, 04544347, 06661346, 474H110AR ROD
77931 ROD, AUTOMATIC CHOKE (STERN DRIVE) Mercruiser
Rating:
83

Buy ROD, AUTOMATIC CHOKE (STERN DRIVE) 77931 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 37
 

Mercruiser entire parts catalog list:

02602347 1987,1988,1989,1990,1991,1992,1993,1994,1995
02608427 1987
03302336 1986
03307332 1982
04544347 1987
06661346 1986,1987,1988,1989
474H110AR 1988,1989,1990,1991

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
430-5
Engine Starter Motor Solenoid : Current Below Normal 444-5
Starter Motor Relay : Current Below Normal This code indicates that there is a problem with the engine starter motor solenoid and/or the electrical circuit on the Electronic Control Module (ECM).
430-6
Engine Starter Motor Solenoid : Current Above Normal 444-6
Starter Motor Relay : Current Above Normal This code indicates that there is a problem with the engine starter motor solenoid and/or the electrical circuit on the ECM.
677-5
Engine Starter Motor Relay : Current Below Normal 444-5
Starter Motor Relay : Current Below Normal This code indicates that there is a problem with the engine starter motor relay and/or the electrical circuit on the ECM.
677-6
Engine Starter Motor Relay : Current Above Normal 444-6
Starter Motor Relay : Current Above Normal This code indicates that there is a problem with the engine starter motor relay and/or the electrical circuit on the ECM.
4210-5
Engine Pre-lube Drive : Current Below Normal 338-5
Engine Pre-Lube Pump Relay : Current Below Normal This code indicates that there is a problem with the prelubrication solenoid and/or the electrical circuit on the ECM.
4210-6
Engine Pre-lube Drive : Current Above Normal 338-6
Engine Pre-Lube Pump Relay : Current Above Normal This code indicates that there is a problem with the prelubrication solenoid and/or the electrical circuit on the ECM. Electrical Checkouts on the Cat® Electronic Technician (ET)
Table 2
Component Electrical Checkout
Engine Starter Solenoid Attempt to start the engine. Once the ECM attempts to energize the solenoid, the code will become active. Refer to the application-specific schematic for the "Engine Starter Motor Solenoid" wiring circuit.
Engine Starter Motor Relay Attempt to start the engine. Once the ECM attempts to energize the solenoid, the code will become active. Refer to the application-specific schematic for the "Engine Starter Motor Relay" wiring circuit.
Prelubrication System Relay Prelubrication Relay Override
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -5 code is active or logged.
Proceed to Test Step 2.
Result: A -6 code is active or logged.
Proceed to Test Step 3.
2. Check the Wiring for an Open Circuit
A. Verify that the harness connector is free of debris, free of corrosion, and securely connected.
B. Disconnect the solenoid from the harness.
C. Connect a jumper wire between the terminals of the harness connector for the affected coil. The coil is replaced with a short circuit.
Create a Short
Result: A -5 code became active during the electrical checkout. The ECM did not detect the jumper wire. There is an open circuit in the wiring between the coil and the ECM connector. There may be a problem with a connector.
Repair: Repair or replace the connectors or the wiring.
Verify that the repair eliminated the problem.
Result: A -6 code is activated during the electrical checkout. The ECM detected the jumper wire. There is a problem with the solenoid.
Repair: Replace the solenoid.
Verify that the repair eliminated the problem.
3. Check the Wiring for a Short Circuit
A. Disconnect the solenoid from the harness.
Create an Open
Result: A -6 code became active during the electrical checkout. The ECM did not detect the open circuit. There is a short circuit in the wiring between the coil and the ECM connector. There may be a problem with a connector.
Repair: Repair or replace the connectors or the wiring.
Verify that the repair eliminated the problem.
Result: A -5 code is activated during the electrical checkout. The ECM detected the open circuit. There is a problem with the solenoid.
Repair: Replace the solenoid.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts rod Mercruiser:

61112
 
61112 ROD, AUTOMATIC CHOKE
00014332, 01751347, 01851333, 01854335, 02287333, 02297343, 02607333, 02608427, 07711346, 08987343, 228801, 260801
35377
 
35377 ROD, PUSH-FUEL PUMP
00014332, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 06661346, 07711346, 08986342, 08987343, 228801, 257B021JS, 260801, 30001854, 37011856, 4052110CR, 4350100KS, 44031854, 4454110AS, 457B100KS, 457B101JS
99948
 
99948 ROD, VALVE PUSH (DOUBLE BALL END)
00014332, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 07711346, 08986342, 08987343, 228801, 257B021JS, 260801, 30001854, 32001876, 4350100KS, 457B100KS, 457B101JS, 457B101KS, 457L101JS
66197
 
66197 ROD, AUTOMATIC CHOKE (INBOARD)
03302336, 03307332, 03308333, 04544347
75589
 
75589 ROD, VALVE PUSH (INLET)
03302336, 03307332, 03308333, 04544347, 06661346, 44541101S, 474H110AR, 474L118JS
75590
 
75590 ROD, VALVE PUSH (EXHAUST)
03302336, 03307332, 03308333, 04544347, 06661346, 44541101S, 474H110AR, 474L118JS
72468
 
72468 ROD, AUTOMATIC CHOKE
02602347, 02608427, 37011856, 44031854, 4454110AS
17339
 
17339 ROD, VALVE PUSH (DOUBLE BALL END)
01751347, 02602347, 02608427, 4350111HS, 443B0002S, 443B1003S, 443B100JS, 457B101JS, 457B111GS
Back to top