864152 Mercruiser LINE, Fuel, Fuel Pump to Filter


864152 LINE, Fuel, Fuel Pump to Filter Mercruiser 40430002S, 424106LRS, 444106LPS, 444236HRS, 4M4102LPS LINE
864152 LINE, Fuel, Fuel Pump to Filter Mercruiser
Rating:
23

Buy LINE, Fuel, Fuel Pump to Filter 864152 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$1,055.00
 

23-08-2021
56.0[25.20] Pounds
-: -
VICKERS PVB5 LSW 21 CM 11 S124 864152 STYLE NEW REPLACEMENT PISTON PUMPS
Compensator: CM COMPENSATOR 250-1500 PSI || Rotation: LEFT HAND CCW ROTATION || Shaft: SPLINE SHAFT || Ports: SIDE PORTS || Core: CORE RETURNS ACCEPTED ON THIS ITEM - CONTACT CUSTOMER SERVICE FOR DETAILS
Number on catalog scheme: 29
 

Compatible models:

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 230-6284 Timing Pin (Camshaft) 1
B 136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
C 298-5564 T40 Torx Socket 1
D 235-0032 Valve Lash Gauge Gp 1
E 8T-5096 Dial Indicator Gp 1
- Magnetic Base and Stand 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03414056
Illustration 2 g03414057
Ensure that Tooling (B) is installed in Hole (Y) in the cylinder block. Use Tooling (B) in order to lock the crankshaft in the correct Position. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
Ensure that Tooling (A) is installed into Hole (X) in camshaft gear (3).
Illustration 3 g03414059
Illustration 4 g03414060
Illustration 5 g03414061
Clean idler gear (3) and inspect the idler gear for wear and damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace the idler gear.
Clean hub (11) and inspect the hub for wear and damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace the hub.
Lubricate hub (11) with clean engine oil. Install hub (10) into idler gear (3). Ensure that oil Hole (Z) is position as shown in the Illustration 4. Ensure that the timing marks are toward the front of the idler gear.
Align the timing marks on idler gear (3), camshaft gear (5), fuel injection pump gear (4). Refer to the Illustration 5. Install the assembly of idler gear (3) and hub (11).
Clean plate (9) and inspect the plate for wear and damage. If necessary, replace the plate.
Lubricate plate (9) with clean engine oil. Align the holes in plate (9) with the holes in hub (11). Install the plate in the original orientation. Note: Ensure that the identification mark TOP is upward.
Install bolts (10) hand tight
Remove Tooling (A) and Tooling (B). Note: Ensure that timing marks are aligned, before removing the Tooling (A) and Tooling (B).
Tighten bolts (10) to a torque of 44 N m (32 lb ft).
Illustration 6 g01996554
Position a new O-ring seal (1) onto plug (2). Install the plug to the cylinder block and tighten the plug to a torque of 21 N m (186 lb in).
Use Tooling (E) in order to check the end play for the idler gear. Refer to Specifications, "Gear Group (Front)" for more information.
Use Tooling (E) in order to check the backlash between the idler gear and the camshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
Use Tooling (E) in order to check the backlash between the idler gear and the crankshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
Use Tooling (E) in order to check the backlash between the idler gear and the fuel injection pump gear. Refer to Specifications, "Gear Group (Front)" for more information.
Lightly lubricate all of the gears with clean engine oil.
Illustration 7 g03378711
Use Tooling (D) in order to check the valve lash. Refer to System Operation, Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for more information.
If necessary, use Tooling (D) and Tooling (C) in order to adjust the valve lash. Refer to System Operation, Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure. End By:
Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install" for the correct procedure.
Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure.


Parts line Mercruiser:

863437
LINE, Fuel, Fuel Cooler to Fuel Rail
863437 LINE, Fuel, Fuel Cooler to Fuel Rail
40430002S, 424106LRS, 424106LTT
864267
 
864267 LINE, Fuel, Fuel Filter to Fuel Pump
40430002S, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS
807953
LINE ASSEMBLY, Fuel
807953 LINE ASSEMBLY, Fuel
4231017L1, 4332087N1, 4441027LE, 444106LPS, 4542067LS, 4652027LE, 4652027M1, 4652227MW, 4M31027LS, 4R42027N1
863664
 
863664 LINE, Fuel, Boost Pump To Fuel Fitler
444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS
863438
LINE, Fuel, Fuel Cooler To Fuel Rail
863438 LINE, Fuel, Fuel Cooler To Fuel Rail
444106LPS, 444236HRS, 4M4102LPS
861565A 2
 
861565A 2 LINE ASSSEMBLY, Fuel Cooler To Fuel Rail
4441027LE, 444106LPS, 4R42027N1
Back to top