809067 Mercruiser METERING ROD KIT


809067 METERING ROD KIT Mercruiser 02602347, 02608427 METERING
809067 METERING ROD KIT Mercruiser
Rating:
83

Buy METERING ROD KIT 809067 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$150.10
 

07-10-2017
2.84[0.90] pounds
Legend: Legend
Legend 809067 Re-Key Kit, 5.587" x 5.587" x 5.587"
Security Devices/Security Devices||legend-re-key-kit||Dimensions: 5.587 X 5.587 X 5.587||Made in: China
$29.22
 

09-03-2023
0.0[0.00] Pounds
-: -
AnzoUSA 809067 Super White 27W Halogen Bulb - Pair
Guaranteed To Improve Your Visibility
 
$23.00
 

07-10-2017
1.00[0.45] pounds
ANZO: ANZO
ANZO 809067 Headlight Bulb
Comes with full manufacturer warranty||Fits multiple makes and models (contact seller with your vehicle for fitment compatibility information)
Number on catalog scheme: 5
 

Compatible models:

02602347   02608427   Mercruiser

Mercruiser entire parts catalog list:

02602347 1987,1988,1989,1990,1991,1992,1993,1994,1995
02608427 1987

Information:

2. Loosen two hose clamps (1).3. Remove hose (2). 4. Remove two bolts (3).5. Remove elbow (5).6. Remove fumes disposal tube (4) for access to the water pump.7. Disconnect coolant conditioner hose (6).8. Remove heater hose (12) (previously removed).9. Loosen hose clamp (15).10. Disconnect lower radiator hose (13).11. Remove two bolts (14) from oil cooler. Check gasket for wear or damage. Replace if necessary.12. Remove four bolts (10).13. Remove water pump cover (11).14. Remove seven long bolts (7).15. Reposition air conditioning lines and oil line (8) after bolts are removed.16. Remove water pump (9). Check seals and O-rings for wear and damage before installation, replace as necessary. For installation of the water pump, reverse the removal steps.17. Fill the cooling system with coolant to correct level. See the Operation & Maintenance Manual.Disassemble Water Pump
*Part of 1P510 Driver Group.Start By:a. remove water pump The water pump seal can be replaced without removing the water pump from the engine. An intermittent leakage of a small amount of coolant from the hole in the water pump housing is not an indication of a water pump seal failure. This is required to provide lubrication for the seal. Replace the water pump seal only if a large amount of leakage or a constant flow of coolant is observed draining from the water pump housing.1. Remove O-ring seal (1) from the adapter.2. Remove adapter (2) from the housing. Remove the O-ring seal from the outside diameter of the adapter.3. Remove bolt (3) and the retainer that hold the impeller on the shaft. 4. Use Tool (A) to remove impeller (4) from the shaft. 5. Remove the spring and seal (5) from the shaft. 6. Remove four bolts (7) from retainer (6) that hold the shaft assembly to the pump housing.7. Remove O-ring seal (8) from the housing. 8. Remove gear and shaft assembly (10) from the housing.9. Remove bolt (9) and the retainer from the shaft assembly. 10. Use a press to remove the shaft assembly from gear (11). Remove the retainer from the shaft assembly. 11. Remove bearing (13), spacer (14) and bearing (12) from the shaft. 12. Remove lip-type seal (15) from the housing.13. Turn the housing over, and remove ceramic ring (16) and the seal.Assemble Water Pump
1. Use 6V1541 Quick Cure Primer to clean shaft (8) and the seal counterbore in the pump housing.2. Install bearing (4), spacer (3) and bearing (2) on shaft (8).3. Put retainer (1) and gear (7) in position on the shaft assembly. Install retainer (6) and bolt (5). 4. Use Tool (A) to install the lip-type seal in the housing as shown. Put a small amount of clean SAE 30 Oil on the lip of the seal. 5. Install a new O-ring seal (10) on the housing.6. Put shaft assembly (9) in position in the housing. Install the bolts that hold the retainer to the housing.
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
7. Put ceramic ring (12) in position in rubber seal (11). Use hand pressure and Tool (B) to install the ceramic ring in the housing.
Avoid contaminating the seal faces with grease or oil. Also, avoid stretching the rubber seal during installation.
The carbon seal assembly must rotate with the water pump shaft after installation.8. Remove the spring from seal assembly (13). Use hand pressure and Tool (B) to install the seal assembly. Push the seal assembly on the shaft until the seal faces make light contact. 9. Install spring (15) on the shaft.10. Put impeller (14) in position on the shaft. Install the washer and bolt that holds it. Tighten the bolt to a torque of 39 3 N m (29 2 lb ft). 11. Install O-ring seal (17) on the outside diameter of the adapter. Put a small amount of clean SAE 30 Oil on the O-ring seal.12. Install O-ring seal (18) on the adapter.13. Put adapter (16) in position on the housing.End By:a. install water pump


Parts metering Mercruiser:

8754
 
8754 METERING JET AND ROD KIT
00014332, 02287333, 02607333, 02608427, 08987343, 260801
8751
 
8751 METERING JET AND ROD KIT
00014332, 02287333, 02607333, 02608427, 08987343, 228801
2994
 
2994 METERING JET AND ROD KIT
00014332, 02287333, 02607333, 02608427, 08986342, 08987343
8544
 
8544 METERING JET AND ROD KIT
02297343, 02602347, 02608427, 07711346
8583
 
8583 METERING JET AND ROD KIT
02602347, 02608427
823726
METERING ROD KIT
823726 METERING ROD KIT
02602347, 02608427
811656
METERING ROD KIT
811656 METERING ROD KIT
02602347, 02608427
809074
 
809074 METERING ROD KIT
02602347, 02608427, 257B021JS, 457B100KS
Back to top