20083 Mercruiser NUT, STARTER SOLENOID TERMINAL (5/16")


20083 NUT, STARTER SOLENOID TERMINAL (5/16") Mercruiser 02287333, 03302336, 03307332, 04706002, 04707333, 04708004, 04856332, 04881333, 08986342, 228801, 2888203, 37011856, 44031854, 6030000ES NUT
20083 NUT, STARTER SOLENOID TERMINAL (5/16") Mercruiser
Rating:
33

Buy NUT, STARTER SOLENOID TERMINAL (5/16") 20083 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 23
 

Mercruiser entire parts catalog list:

02287333 1983
03302336 1986
03307332 1982
04706002 1982,1983
04707333 1983
04708004 1984
04856332 1982
04881333 1983
08986342 1982,1983
228801 1981,1982
2888203 1973,1974,1975,1976,1977
37011856 1986,1987
44031854 1984
6030000ES 1992

Information:

1. Check each bearing cap (1) for its location on the engine. Each cap has an arrow which is toward the front of the block and a number which gives the location of that cap. Keep each bearing with the correct cap.2. Remove bearing caps No. 2 through No. 4. Remove thrust plates from No. 3 upper bearing.
Be careful not to cause damage to the crankshaft journals when the crankshaft is removed.
3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 5 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 270 lb. (122 kg). 4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface 0.025 0.02 in. (6.4 0.5 mm).2. Install dowel (2) until it is extended from the surface 0.16 0.02 in. (4.1 0.5 mm). 3. Heat crankshaft gear (3) to a maximum temperature of 400°F (204°C). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2).4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft.
Do not cause damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block. For more detail about installation of main bearings see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS.6. Check the bearing clearance with Plastigage.7. Put clean engine oil on the bolts for caps No. 1 and No. 5. Install No. 1 and No. 5 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block. 8. Install thrust plates (5) for the No. 3 upper main bearing. Install the thrust plates with the side that has the identification "Block Side" toward the cylinder block.9. Put clean oil on the bolts for caps No. 2 through No. 4. Install caps No. 2 through No. 4 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows: a) Tighten the bolts on the tab end of the caps first to a torque of 190 10 lb.ft. (260 14 N m).b) Tighten the bolts on the other end of the caps to a torque of 190 10 lb.ft. (260 14 N m).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. 11. Check the play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.006 to 0.020 in. (0.152 to 0.508 mm). The maximum end play with used thrust plates is 0.035 in. (0.89 mm).end by:a) install pistonsb) install flywheel housingc) install timing gear coverd) install oil pump


Parts nut Mercruiser:

35814
 
35814 NUT,FUEL FILTER SCREW
00014332, 01206002, 01207333, 01326013, 01402414, 01407333, 01701335, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 04707333, 04708004, 04881333, 06661346, 07711346, 08986342, 08987343,
47626
 
47626 NUT, OIL LEVEL GAUGE TUBE INBOARD
01701335, 02287333, 02297343, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 04856332, 04881333, 08986342, 228801, 4454110AS, 474H110AR
46887
 
46887 NUT, SHIFT CABLE ADAPTOR STUD (1/4-28)
02287333, 03302336, 03307332, 04706002, 04707333, 08986342, 228801
25269
 
25269 NUT, MOUNTING BRACKET SCREW
01206002, 01207333, 01326013, 01406002, 01407333, 01701335, 04706002, 04707333, 04708004, 04856332, 04881333, 37011856, 44031854
64015
 
64015 NUT, (.250-20), ALTERNATOR TERMINAL
00019003, 01207333, 01321017, 01326013, 01402414, 01407333, 01751347, 02297343, 02602347, 02608427, 03307332, 03308333, 04544347, 06661346, 257B021JS, 37011856, 4052110CR, 4211015L1, 4211025RS, 4211025TS, 4211025TT, 4231017L1, 430B00001, 4332087N1, 4
52901
 
52901 NUT, TAILSTOCK SCREW
30001854, 37011856, 44031854
Back to top