25899 Mercruiser NUT, PULLEY TO HYDRAULIC PUMP


25899 NUT, PULLEY TO HYDRAULIC PUMP Mercruiser 01206002, 01207333, 01326013, 01406002, 01407333 NUT
25899 NUT, PULLEY TO HYDRAULIC PUMP Mercruiser
Rating:
18

Buy NUT, PULLEY TO HYDRAULIC PUMP 25899 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 23
 

Compatible models:

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
1180-3
Engine Turbocharger 1 Turbine Inlet Temperature : Voltage Above Normal 3908-3
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Voltage Above Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1180-4
Engine Turbocharger 1 Turbine Inlet Temperature : Voltage Below Normal 3908-4
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Voltage Below Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1180-8
Engine Turbocharger 1 Turbine Inlet Temperature : Abnormal Frequency, Pulse Width, or Period 3908-8
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Abnormal Frequency, Pulse Width, or Period If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-3
Engine Turbocharger 2 Turbine Inlet Temperature : Voltage Above Normal 3909-3
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Voltage Above Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-4
Engine Turbocharger 2 Turbine Inlet Temperature : Voltage Below Normal 3909-4
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Voltage Below Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-8
Engine Turbocharger 2 Turbine Inlet Temperature : Abnormal Frequency, Pulse Width, or Period 3909-8
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Abnormal Frequency, Pulse Width, or Period If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
Illustration 1 g06323402
Schematic of the PWM sensors for the sensor signal circuit
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -3 code is active or logged.
Proceed to Test Step 2.
Result: A -4 code is active or logged.
Proceed to Test Step 3.
Result: A -8 code is active or logged.
Proceed to Test Step 5.
2. Create a Short at the Sensor Connector
A. Remove electrical power from the engine.
B. Disconnect the sensor with the active -3 code.
C. Install the jumper wire between the following terminals at the sensor connector:
- Pin 2 (sensor return) and Pin 3 (sensor signal)
D. Connect Cat ET.
E. Use Cat ET to monitor the following:
- -4 code
F. Remove electrical power from the engine.
Create a Short
Result: A -4 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
Result: A -4 code did not become active.
Proceed to Test Step 4.
3. Create an Open at the Sensor Connector
A. Remove electrical power from the engine.
B. Disconnect the sensor with the active -4 code.
C. Connect Cat ET.
D. Use Cat ET to monitor the following:
- -3 code
E. Remove electrical power from the engine.
Create an Open
Result: A -3 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
Result: A -3 code did not become active.
Proceed to Test Step 4.
4. Check the 8 VDC Supply Voltage at the Sensor Connector
A. Apply electrical power to the engine.
B. Measure the voltage at the following pin locations of the affected sensor connector:
- Pin 1 and Pin 2
C. Reconnect the sensor.
Supply Voltage
Result: The supply voltage is approximately 8.0 0.2 VDC
Proceed to Test Step 8.
Result: The supply voltage is not approximately 8.0 0.2 VDC.
Repair: There is a short in the wiring harness to the battery. Repair or replace the wiring harness.
If the problem is not resolved, proceed to Test Step 5.
5. Check the PWM Circuit for an Open
A. Remove electrical power from the engine.
B. Disconnect the sensor with the active -8 code.
C. Disconnect the J2 connector


Parts nut Mercruiser:

32219
 
32219 NUT, BRACKET AND FLYWHEEL HOUSING SCREW
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01701335, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 04708004, 04856332, 04881333,
20220
 
20220 NUT, FRONT MOUNTING BRACKET ADJUSTING STUD (TOP)
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01701335, 04706002, 04707333, 04708004, 04856332, 04881333, 2140208, 2165203, 2165208, 2250507, 4111021L1, 430B00001, 430L000JS
35814
 
35814 NUT,FUEL FILTER SCREW
00014332, 01206002, 01207333, 01326013, 01402414, 01407333, 01701335, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 04707333, 04708004, 04881333, 06661346, 07711346, 08986342, 08987343,
24656
 
24656 NUT, MOUNTING BRACKET TO HYDRAULIC PUMP THRU BOLT
00014332, 00019003, 01321017, 01326013, 03301310, 03302336, 03307332, 2140208, 2165208, 2250507, 5000165CE, 6030000ES
94330
 
94330 NUT, STARTER SOLENOID TERMINAL (1/4-20)
00014332, 00019003, 01207333, 01321017, 01326013, 01402414, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03301310, 03307332, 03308333, 04544347, 06661346, 07711346, 08987343, 257B021JS, 30001854, 32001876,
26484
 
26484 NUT, SHIFT LEVER STUD
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01701335, 01851333, 02287333, 02297343, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 04708004, 04856332, 04881333, 08986342, 08987343, 228801, 26
21923
 
21923 NUT, SWITCH TERMINAL STUD (8-32)
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 02287333, 02607333, 03302336, 03307332, 08986342, 228801, 260801
33272
 
33272 NUT, FAN AND PULLEY TO ROTOR
01206002, 01207333, 01326013, 01406002, 01407333, 08986342
Back to top