879172096 Mercruiser NUT


879172096 NUT Mercruiser 40200002D, 40200002G NUT
879172096 NUT Mercruiser
Rating:
78

Buy NUT 879172096 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Compatible models:

40200002D   40200002G   Mercruiser

Mercruiser entire parts catalog list:

40200002D 1998
40200002G 1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 1U-6684 Piston Ring Compressor 1
C 227-4390 E12 Torx Socket 1
D 8T-3052 Degree Wheel 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
If the connecting rod caps were temporarily installed, remove the connecting rod caps. If necessary, thoroughly clean all of the components.
Apply clean engine oil to the cylinder bore, piston rings, outer surface of the piston and the bearing shells for the connecting rod. Note: Install the bearing shells for the connecting rods dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil to the bearing shells for the connecting rods during final assembly.Note: Ensure that the piston and the connecting rod assembly are installed in the correct cylinder.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom center position. Lubricate the crankshaft pin with clean engine oil.
Illustration 1 g02013213
Install Tooling (B) onto piston (4). Note: Ensure that Tooling (B) is installed correctly and that piston (4) can easily slide from the tool.Note: The arrow on the top of the piston must be toward the front of the engine. The locating tab for the bearing shell of the connecting rod must be on the same side of the engine as the piston cooling jet.
Carefully push the piston and the connecting rod assembly into the cylinder bore and onto the crankshaft pin. Note: Do not damage the finished surface of the crankshaft pin.
Illustration 2 g02447296
Install connecting rod cap (2) onto connecting rod (1). Note: Ensure that dot punched number in Position (X) on connecting rod cap (2) matches dot punched number in Position (X) on connecting rod (1). Ensure the correct orientation of connecting rod cap (2). The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old bolts in order to secure the connecting rod cap.
Install new bolts (3) to connecting rod (1). Use Tooling (C) in order to tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts for an additional 120 degrees in a clockwise direction. Use Tooling (C) and Tooling (D) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft in order to ensure that there is no binding.
Repeat Step 2 through Step 9 in order to install the remaining pistons and connecting rods. End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install" for the correct procedure.
Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for the correct procedure.


Parts nut Mercruiser:

898101772
 
898101772 NUT, (M8)
40200002D, 40200002G
898101544
 
898101544 NUT
40200002D, 40200002G, 40280002D, 40420002D
879172097
 
879172097 NUT
40200002D, 40200002G
898101541
 
898101541 NUT
40200002D, 40200002G, 40280002D, 40420002D
879172098
 
879172098 NUT
40200002D, 40200002G
897345010
898101718
 
898101718 NUT
40200002D, 40200002G
879275
 
879275 NUT
40200002G, 40280002D, 40420002D
Back to top