882680 Mercruiser NUT


882680 NUT Mercruiser 4V71222ND, 4V71222PD, 4V71222TD NUT
882680 NUT Mercruiser
Rating:
103

Buy NUT 882680 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$8.93
 

07-10-2017
.6[0.00] pounds
MERCURY: MERCURY
New Mercury Mercruiser Quicksilver Oem Part # 882680 Nut
Number on catalog scheme: 14
 

Compatible models:

Mercruiser entire parts catalog list:

4V71222ND 1998
4V71222PD 1998
4V71222TD 1998

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1U-8221     Lifting Strap     1    Start By:
Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
If the engine is equipped with a balancer, remove the balancer. Refer to Disassembly and Assembly, "Balancer - Remove". If the engine is not equipped with a balancer, remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
If the crankshaft has been reground or if the crankshaft has been replaced, the height of the piston above the cylinder block must be inspected. It is necessary to remove the cylinder head in order to inspect the height of the piston above the cylinder block.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The engine should be mounted on a suitable stand and placed in the inverted position.
If necessary, remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove". Remove the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Remove".If the cylinder head, the pistons and the connecting rods have not been removed, remove the connecting rod caps. Refer to Disassembly and Assembly, "Connecting Rod Bearings - Remove".
Illustration 1 g01253717
Typical example
Remove allen head screws (1) . Remove bridge piece (2) .
Ensure that the bearing caps are marked for the location and orientation.
Illustration 2 g01253719
Typical example
Remove bolts (3) and bearing caps (4) from the cylinder block.
Illustration 3 g01253146
Typical example
Illustration 4 g01253137
Typical example
Remove lower bearings (5) from bearing caps (4) . Take care not to displace dowels (6) . For number three bearing cap, remove thrust washers (7) . Keep the lower bearing and the thrust washers with the respective bearing caps.Note: The lower bearings are plain bearings that have no oil holes. The dowels may remain in the bearing cap or in the cylinder block.
Illustration 5 g01254099
Typical example
Attach Tooling (A) and a suitable lifting device to crankshaft (8) . Carefully lift the crankshaft out of the cylinder block. The weight of the crankshaft is approximately 30 kg (66 lb).Note: Do not damage any of the finished surfaces on the crankshaft, when the crankshaft is removed from the engine.
Illustration 6 g01254104
Typical example
Illustration 7 g01889993
No. 1 Upper Main Bearing
Illustration 8 g03326558
Remaining Original Upper Main Bearing
Remove upper bearings (9) from the cylinder block. Keep the upper bearings with the respective bearing caps.Note: Number one upper main bearing has an oil slot. See Illustration 7. If the engine is equipped with the original main bearing shells, all other upper shells except number one will have a slot and two oil holes. See Illustration 8.If the engine has had replacement main bearing shells, the upper main bearing shells will all have a groove and an oil slot.
Remove thrust washers (10) from number three bearing in the cylinder block.
If necessary, remove the crankshaft gear. Refer to Disassembly and Assembly, "Crankshaft Gear - Remove and Install".


Parts nut Mercruiser:

40021 3
 
40021 3 NUT
428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4S42028UT, 4S42028UU, 4S420P8UE, 4V71222PD, 4V71222TD, 5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
882682
 
882682 NUT
4V71222ND, 4V71222PD, 4V71222TD
882331
 
882331 NUT, (M10), Pulley, Flange
4V71222ND, 4V71222PD, 4V71222TD
826708 17
 
826708 17 NUT, (.500-20)
40430002S, 40500006T, 4211025RS, 4211025TS, 4211025TT, 424106LRS, 424106LTT, 444106LPS, 444236HRS, 4M11025RS, 4M11025TS, 4M11025TT, 4M4102LPS, 4M4102LRS, 4M4102LTS, 4V71222ND, 4V71222PD, 4V71222TD
806709 12
 
806709 12 NUT
4V71222ND, 4V71222PD
826708 15
 
826708 15 NUT, (.437-20)
40280002D, 40420001D, 40420002D, 40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4A72040ND, 4C72040TD, 4C8204DLD, 4M11025R
826710 13
 
826710 13 NUT, (.375-24) Stainless Steel
4V71222PD, 4V71222TD, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910TP, 5E31910TS, 5E32200TP, 5E32900TS, 5E36200TP, 5E36200TS, 5E36210TP, 5E36210TS, 5E36800TP, 5E36800TS, 5E36810T
40138 6
 
40138 6 NUT, (M6) Stainless Steel
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS, 4V71222PD, 4V71222TD
Back to top