21720 Mercruiser "O" RING, HYDRAULIC PUMP TO CONTROL VALVE


21720 "O" RING, HYDRAULIC PUMP TO CONTROL VALVE Mercruiser 2250507, 6030000ES O
21720 "O" RING, HYDRAULIC PUMP TO CONTROL VALVE Mercruiser
Rating:
33

Buy "O" RING, HYDRAULIC PUMP TO CONTROL VALVE 21720 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

2250507   6030000ES   Mercruiser

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
B     9S-3263     Thread Lock Compound     1    
C     8T-2998     Lubricant     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01039504
Thoroughly clean the gasket material from the cylinder block.
Install a new gasket (25) and O-ring seals (26) on the cylinder block.Note: On newer blocks, an integral seal is used instead of O-ring seals (26) and gasket (25) .
Illustration 2 g00576208
Illustration 3 g01032116
Thoroughly clean all gasket material from both sides of plate (23). Install plate (23) and bolts (24) .
Install shaft assembly (20). Apply Tooling (B) to the studs and to the bolt for shaft assembly (20). Tighten the nuts and the bolt for shaft assembly (20) to a torque of 55 10 N m (41 7 lb ft).Note: The backlash for the camshaft gear and for the adjustable idler gear will need to be readjusted if shaft assembly (19) has been removed, loosened, or moved in any way. The camshaft gear must be installed and the adjustable idler gear must be removed in order to perform the backlash adjustment procedure. Refer to Testing and Adjusting, "Gear Group (Front) - Time".
Install shaft assembly (19). Do not tighten the nuts and the bolt for shaft assembly (19) at this time. The nuts and the bolt for shaft assembly (19) will need to be tightened when the backlash is adjusted.
Apply Tooling (B) to bolts (22). Install shaft assembly (21). Tighten bolts (22) to a torque of 55 10 N m (41 7 lb ft) in the following sequence: (1, 3, 4, 5, 2, 1, 2, 3, 4, 5, 1).
Illustration 4 g01074541
Illustration 5 g00516404
Put cluster gear (15) on shaft assembly (21). Ensure that Timing Marks (V) are aligned on the cluster gear and on the crankshaft gear. Apply Tooling (B) to bolts (16). Install plate (17) and bolts (16). Tighten bolts (16) to a torque of 30 7 N m (22 5 lb ft).
Illustration 6 g01074542
Position idler gear (11) on shaft assembly (20). Apply Tooling (B) to bolts (12). Install plate (13) with the oil groove toward the gear face. Install bolts (12) and tighten the bolts to a torque of 30 7 N m (22 5 lb ft).
Illustration 7 g01074546
Note: Skip Step 9 if shaft assembly (19) has been removed, loosened, or moved in any way. The backlash for the camshaft gear and for the adjustable idler gear will need to be readjusted. The camshaft gear must be installed and the adjustable idler gear must be removed in order to perform the backlash adjustment procedure. Refer to Testing and Adjusting, "Gear Group (Front) - Time".
Position adjustable idler gear (7) on shaft assembly (19). Apply Tooling (B) to bolts (8). Install plate (9) and bolts (8). Tighten bolts (8) to a torque of 30 7 N m (22 5 lb ft).
Illustration 8 g00576240
Illustration 9 g01039529
Install O-ring seals (5) and (6) in seal assembly (3). Lubricate seal (6) with a 50/50 mixture of Tooling (C) and engine oil.
Assemble thrust plate (1) and seal assembly (3). Apply Tooling (B) to bolts (2). Hold the assembly in position and install bolts (2). Evenly tighten bolts (2) until seal assembly (3) and O-ring seal (5) are seated against the cylinder head.Note: Be careful in order to ensure that O-ring seal (5) stays in the groove in seal assembly (3) .
Install adapter (4). Ensure that the dowel in adapter (4) engages the hole in the camshaft.
Adjust the backlash for the camshaft gear and for the adjustable idler gear, if necessary. Refer to Testing and Adjusting, "Gear Group (Front) - Time".Note: The camshaft gear must be installed and the adjustable idler gear must be removed in order to perform the backlash adjustment procedure.End By: Install the front housing. Refer to Disassembly and Assemb


Parts o Mercruiser:

33504
 
33504 "O" RING, BELL HOUSING
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000147JS, 5000150DP, 5000165CE, 5111200LP
55801
 
55801 "O" RING, UPPER DRIVE SHAFT
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000165CE, 5220200AS, 91331015
32546
 
32546 "O" RING, TOP COVER SEALING
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5220200AS, 5S21800TS, 91331015
25439
 
25439 "O" RING, UNIVERSAL JOINT
00014332, 00019003, 01207333, 01321017, 01326013, 01402414, 01407333, 02287333, 02602347, 02607333, 02608427, 03301310, 08986342, 08987343, 2140208, 2165208, 2250507, 228801, 257B021JS, 260801, 457B100KS, 5000150DP, 5000165CE, 5120150AR, 5220200AS, 9
70937
 
70937 "O" RING, OIL SEAL CARRIER
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5220200AS, 5C30150FS, 5S21800TS, 6020006JS, 91331015
39695
 
39695 "O" RING, REAR COVER
01321017, 03301310, 5220200AS, 6030000ES, 91331015
54030
 
54030 "O" RING, GEAR HOUSING
01321017, 03301310, 5220200AS, 6030000ES, 91331015
34821
 
34821 "O" RING, BEARING CARRIER
01321017, 03301310, 5120136JS, 5120150AR, 5120150R1, 5220200AS, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 6020006JS, 6030000ES, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6511102N1, 6811001N1
Back to top