49952 Mercruiser OIL SEAL, CRANKCASE COVER


49952 OIL SEAL, CRANKCASE COVER Mercruiser 2165203, 2165208 OIL
49952 OIL SEAL, CRANKCASE COVER Mercruiser
Rating:
58

Buy OIL SEAL, CRANKCASE COVER 49952 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

Compatible models:

2165203   2165208   Mercruiser

Mercruiser entire parts catalog list:

2165203 1973,1974,1975,1976,1977
2165208 1978

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tooling is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Illustration 1 g06132053
If necessary, follow Step 1.a through Step 1.d to install bracket (31) to fuel injection pump (19).
Position fuel injection pump (19) in a suitable stand.
Position bracket (31) onto fuel injection pump (19). Ensure that the bracket is correctly orientated.
Install bolts (30) hand tight.
Tighten bolts (30) to a torque of 22 N m (195 lb in).
If necessary, install flow control valve (12). Refer to Disassembly and Assembly, "Flow Control Valve - Remove and Install" for the correct procedure.
Illustration 2 g06136408
The Angle (Y) should be 43 degrees. The Angle (Z) should be 18 degrees
Position key (35) on the shaft on fuel injection pump (19) in the position as shown in Illustration 2
Install a new O-ring seal (28) to fuel injection pump (19). Ensure that the O-ring seal is correctly installed to the groove in the fuel injection pump.
Illustration 3 g03674811
Use Tooling (A) to rotate the crankshaft so that number one piston is at Top Dead Center Position on the compression stroke.
If necessary, install Tooling (B) to the lock the crankshaft in the correct position.Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the crankshaft during repairs.
Remove Tooling (B) from the crankshaft. Use Tooling (A) to rotate the crankshaft in a counter clockwise direction by 80 degrees. Refer to Illustration 3 for the correct positioning.
Illustration 4 g06136413
Illustration 5 g06131558
Illustration 6 g06136427
Inspect the bore in front housing (29) for damage. If the bore is damaged, replace the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" and Disassembly and Assembly, "Housing (Front) - Install" for the correct procedure
Carefully install fuel injection pump (19) to front housing (29). Ensure that the bore in the front housing is not damaged as the fuel injection pump is installed.Note: The fuel injection pump should be supported by hand as the bolts are installed.
Ensure that key (35) aligns correctly with fuel injection pump gear (3). Ensure that the fuel injection pump gear is correctly seated onto fuel injection pump shaft (4). Ensure that the key is not dislodged from fuel injection pump shaft (4) as fuel injection pump (19) is installed into the front housing (29).
Install bolts (30) to fuel injection pump (19) hand tight.
Install a new spring washer (6) (not shown) and install nut (5) hand tight.
Illustration 7


Parts oil Mercruiser:

58203
 
58203 OIL SEAL UNIT, CRANKSHAFT REAR BEARING
00014332, 01206002, 01207333, 01326013, 01406002, 01407333, 01851333, 01854335, 02287333, 02297343, 02607333, 02608427, 08986342, 08987343, 2165203, 2165208, 228801, 260801, 30001854
49288
 
49288 OIL FILTER CAP ASSEMBLY, ROCKER COVER
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 02287333, 02297343, 02607333, 02608427, 07711346, 08986342, 08987343, 2165203, 2165208, 228801, 260801
36405
 
36405 OIL PUMP ASSEMBLY
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 2165203, 2165208, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
52731
 
52731 OIL FILTER ASSEMBLY
00014332, 02287333, 02607333, 02608427, 03302336, 03307332, 07711346, 08986342, 08987343, 2165203, 2165208, 228801, 260801
54111
 
54111 OIL FILTER ASSEMBLY
01206002, 01207333, 01326013, 01406002, 01407333, 02297343, 03307332, 03308333, 04544347, 04706002, 04707333, 04708004, 04856332, 04881333, 07711346, 2165203, 2165208, 37011856
59342
32541
 
32541 OIL SEAL, GIMBAL RING
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000165CE
Back to top