807420 Mercruiser OIL HOSE


807420 OIL HOSE Mercruiser 442B110GD, 442B115KD OIL
807420 OIL HOSE Mercruiser
Rating:
63

Buy OIL HOSE 807420 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$13.31
 

20-08-2024

US: S Logistics Doncaste
MURNELAP for Anvil Mark 3" Non-Mortise Hinge (Brass), 807420
MURNELAP For Anvil Mark 3" Non-Mortise Hinge (Brass), 807420 || Enhance your home decor with modern and sleek design elements. || Elevate your bathroom or kitchen with this stylish and functional hardware piece. || Constructed from premium materials to withstand daily wear and tear. || Please ensure a precise fit by reviewing the product's appearance in the photo and cross-checking it with the specified dimensions.
$18.07
 

14-06-2023
1.0[0.45] Pounds
-: -
Dorman 807420 - Cap Screw - Part # 807-420
Cap Screw-Hex Head-Grade 5- 1/2-20 x 2 In.
$81.13
 

07-10-2017

Enerpac: Enerpac
Enerpac HP-2007 Leg (807420)
Number on catalog scheme: 15
 

Compatible models:

442B110GD   442B115KD   Mercruiser

Mercruiser entire parts catalog list:

442B110GD 1994,1995,1996,1998
442B115KD 1997

Information:


Typical Example1. Remove bolts (1) from the alternator bracket.2. Remove the bolts that hold plate (3), and remove the plate.3. Disconnect water line (2) from the air compressor (if equipped). Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 4. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.5. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
6. Remove the gasket and seals from the spacer plate.Install Cylinder Head Assembly
Be sure a new gasket has been installed between the spacer plate and the cylinder block. See the topic, Remove & Install Spacer Plate. 1. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (1) and two O-ring seals (2). 2. Fasten a hoist, and put cylinder head assembly (3) in position on the cylinder block.3. Put clean engine oil on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown in illustration A87019P4. a. Tighten bolts 1 through 20 in number sequence to a torque of 270 25 N m (200 18 lb ft).b. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb ft).c. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb ft) by hand.d. Install the rocker shaft assemblies and push rods. See the topic, Install Rocker Shaft Assemblies & Push Rods.e. Tighten bolts 21 through 26 in number sequence to a torque of 270 25 N m (200 18 lb ft).f. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb ft).g. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb ft) by hand.h. Tighten the 3/8" bolts to a torque of 43 7 N m (32 5 lb ft). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb ft).4. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in) for intake and 0.76 mm (.030 in) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb ft).5. Install the valve cover bases and the inner fuel lines. See the topic, Install Rocker Shaft Assemblies & Push Rods.6. Install the valve covers. See the topic, Install Valve Covers.
Typical Example7. Install plate (4).8. Connect the water line to the air compressor (if equipped).9. Install bolts (5) for the alternator bracket.End By:a. install exhaust manifoldb. install fuel injection linesc. install aftercooler housingd. install water temperature regulatore. install rocker shaft assemblies and push rods


Parts oil Mercruiser:

816795
 
816795 OIL PUMP
442B110GD, 442B115KD
805287A 1
 
805287A 1 OIL PRESSURE GAUGE KIT
40420001D, 428B116KD, 442B110GD, 442B115KD, 473B116KD, 473B1F0GS, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
806103T
OIL FILTER ADAPTOR
806103T OIL FILTER ADAPTOR
442B110GD, 442B115KD
801124680
OIL RESERVOIR TANK
801124680 OIL RESERVOIR TANK
40200002D, 40200002G, 40280001D, 40420001D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
801285638
OIL SEPARATOR
801285638 OIL SEPARATOR
442B110GD, 442B115KD
77653101
 
77653101 OIL DRAIN TUBE
442B110GD, 442B115KD
854087
 
854087 OIL PUMP
40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
855487
 
855487 OIL HOSE-RETURN
40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND
Back to top