858088K01 Mercruiser OIL, Gallons @ 3


858088K01 OIL, Gallons @ 3 Mercruiser 40500120U, 41000008E, 41510P1UE, 4S420P8UE OIL
858088K01 OIL, Gallons @ 3 Mercruiser
Rating:
38

Buy OIL, Gallons @ 3 858088K01 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Compatible models:

Mercruiser entire parts catalog list:

40500120U 1998
41000008E 1998
41510P1UE 1998
4S420P8UE 1998

Information:

Start By:
Install the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install".
Connect the frame lock link. Refer to Disassembly and Assembly, "Frame Lock Link - Separate and Connect".
Purge the air system. Refer to Disassembly and Assembly, "Air System Pressure - Purge/Charge".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hot coolant, steam and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove filler cap slowly to relieve pressure only when engine is stopped and radiator cap is cool enough to touch with your bare hand.Cooling System Conditioner contains alkali. Avoid contact with skin and eyes.
Personal injury can result from hot oil or hot components.At operating temperature, oil is hot and under pressure. Hot oil can cause burns.Remove the fill cap only when the engine is stopped, and the fill cap is cool enough to touch with your bare hand.Do not allow hot oil or components to contact skin.
Note: Install caps and plugs on all openings in order to prevent dirt or debris from entering the system. Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal components.Note: For easier assembly, mark all hose assemblies, tube assemblies, wire harnesses and cables for identification purposes.
Illustration 1 g00608610
The view is on the right side of the engine end frame under the left side of the engine.
Drain the cooling system. Loosen drain plug (1) in order to drain the cooling system.
Refer to Operation and Maintenance, "Cooling System Coolant (ELC) - Change" for the appropriate procedure to drain the cooling system. The capacity of the cooling system is 500 L (132 US gal).
Illustration 2 g00616957
Disconnect tube assembly (2) from the inlet of air compressor (3) .
Illustration 3 g00616959
Disconnect hose assembly (4), hose assembly (5), and hose assembly (6) .
Illustration 4 g00616962
Disconnect hose assembly (7) .
Remove tube assembly (8) .
Illustration 5 g00616964
Disconnect hose assembly (9) and hose assembly (10) .
Illustration 6 g00616966
Position a suitable lifting device around air compressor (3). Remove three bolts (11) and the washers in order to remove air compressor (3). Remove the air compressor. The weight of the air compressor is 32 kg (70 lb).Installation Procedure
Note: Verify that all of the components of the air compressor are clean and free of foreign material prior to installation.Note: Check all of the O-ring seals and the components for wear or damage. Replace the components, if necessary. Lubricate the O-ring seals lightly with the lubricant that is being sealed.
Illustration 7 g00616966
Position a suitable lifting device around air compressor (3). Position air compressor (3) for installation. Install three bolts (11) and the washers. The weight of the air compressor is 32 kg (70 lb).
Illustration 8 g00616964
Connect hose assembly (9) and hose assembly (10) .


Parts oil Mercruiser:

36405
 
36405 OIL PUMP ASSEMBLY
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 2165203, 2165208, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
93924
 
93924 OIL SEAL
00014332, 01207333, 01402414, 01407333, 02287333, 02602347, 02607333, 02608427, 08986342, 08987343, 228801, 257B021JS, 260801, 40280002D, 40420001D, 40420002D, 40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 42
97335
 
97335 OIL SEAL, CRANKCASE FRONT COVER
00014332, 01207333, 01402414, 01407333, 01751347, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 07711346, 08986342, 08987343, 228801, 260801, 30001854, 32001876, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B0000
14240
 
14240 OIL SEAL, CRANKSHAFT (REAR - FULL CIRCLE)
00014332, 01751347, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 07711346, 08987343, 257B021JS, 30001854, 32001876, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 4262C01JT, 430B00001, 430L000JS, 4350104JS, 4350111HS
809910
OIL PAN
809910 OIL PAN
257B021JS, 40500006T, 40500010T, 40500010U, 40500120U, 4332087N1, 4350100KS, 4350104JS, 4350104KS, 4350118JS, 4350118KS, 4441027LE, 444106AM1, 444106LPS, 444236HRS, 457B100KS, 457B101JS, 457B101KS, 457L101JS, 4M11025LS, 4M11025RS, 4M11025TS, 4M11025T
858087K01
 
858087K01 OIL, Quarts @ 6
40500120U, 41000008E, 41510P1UE, 4S420P8UE
Back to top