818381 1 Mercruiser PINION STUD


818381 1 PINION STUD Mercruiser 4454110GE, 45021102S PINION
818381 1 PINION STUD Mercruiser
Rating:
23

Buy PINION STUD 818381 1 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$59.99
 

16-02-2023

-: -
Online Auto Supply Table Top Cylinder Seal Kit for Coats Rim Clamp Tire Changer 8183811, 8182080
$129.00
 

18-03-2022

-: -
Pro Tek Replacement Table Top Shaft for Tire Changer Coats Rim Clamp 5060AX, 5060EX, 7060AX, 7060EX,
Replacement Shaft & Seal Kit for Table Top Cylinder for COATS Rim Clamp tire changer machines. || Direct replacement || 1" Diameter || Reference Part Number 8181629 8183811 || 5040A 5040E 50x 60x 70x 50xx Series Tire Changer 6050A 6050E 6050AX 6050EX 6060AX 6060EX 6065AX 6065EX 7xxx Series Tire Changer APX80A APX80E APX90A APX90E GTS50, GTS60, GTS70 and GTS-90 Rim Clamp Tire Changers RC 45 RC 55 RC200EX, RC150EX Tire Changer
$33.92
 

20-01-2023

-: -
Pro Tek Replacement Table Top Seal Kit for Coats Rim Clamp 50, 70 & APX Series tire Changers.
Fits Coats Rim Clamp Machine || Table Top Cylinder || Ref Part Number: 8183811, 183811
Number on catalog scheme: 30
 

Compatible models:

4454110GE   45021102S   Mercruiser

Mercruiser entire parts catalog list:

4454110GE 1995
45021102S 1992,1993

Information:

4. Disconnect heater hose (1) from the housing assembly.5. Remove the hose from the housing assembly on the water pump to the inlet elbow on the radiator.6. Remove bolts (2) that hold the housing assembly in position. Remove housing assembly (3). 7. Remove tube assembly (5).8. Remove four bolts (4). 9. Remove nuts (6) from behind the water pump. Remove water pump (7).Install Water Pump
1. Check the condition of the seal in the housing assembly for the water pump. If the seal has damage, use new parts for replacement. 2. Put water pump (1) in position on the timing gear cover. Install nuts (2) that hold it. 3. Install four bolts (3).4. Install the tube assembly to the water temperature regulator housing on the right side of the machine. 5. Install housing assembly (5) over the water pump. Install the bolts that hold it.6. Install the hose from the water pump to the inlet elbow on the radiator.7. Connect heater hose (4) to the housing assembly.8. Install the vee belt set for the fan.9. Install the panel over the water pump. The location of the panel is on the left side of the machine.10. Fill the cooling system with coolant to the correct level. See MAINTENANCE GUIDE. Disassemble Water Pump
START BY:a) remove water pump 1. Remove O-ring seal (1) from adapter (2).2. Remove adapter (2) with a screwdriver. Remove the seal from the edge of adapter (2).3. Remove bolt (3) and washer. 4. Remove impeller (4) from the water pump housing with tooling (A). 5. Remove seal assembly (5). Remove ring and seal (6). 6. Remove the bolt and washer that hold gear (7) on the water pump shaft.7. Remove gear (7) with tooling (B).8. Remove bolts and retainer (9).9. Remove O-ring seal (8). 10. Remove shaft (10) and bearings as a unit.11. Remove bearing (11), spacer (12) and bearing (13) from shaft (10).12. Remove lip type seal from the gear side of the water pump. Remove ring and seal from the impeller side of the water pump.Assemble Water Pump
1. Put clean engine oil on the lip seal (1). Install seal (1) with the lip of the seal toward the outside with tooling (A). 2. Install bearing (4), spacer (3) and bearing (5) on shaft (2). Install shaft (2) in the pump housing. 3. Install retainer (7) and O-ring seal (8).4. Install gear (6). Install the washer and bolt that hold gear (6) to shaft (2).
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest of the ring toward the carbon seal assembly.
5. Put ceramic ring (10) in position in the rubber seal (9). Use hand pressure and the tool (which is with the replacement ring) to install the ceramic ring in the housing. 6. Remove spring (12) from seal assembly (11). Use hand pressure and the tool (which is with the replacement ring) to install the seal (11) assembly. Push seal assembly on the shaft until the seal face makes light contact.7. Install spring (12) on the shaft. 8. Install impeller (14) and the washer and bolt (13) that hold the impeller to the pump shaft. Tighten the bolt to a torque of 39 3 N m (28 2 lb.ft.). 9. Put clean engine oil on the O-ring seals (15). Install the O-ring seals on adapter (16).10. Install the adapter (16) in the pump housing with the notch in alignment with dowel (17).END BY:a) install water pump


Back to top