65545 Mercruiser PLATE, TRANSOM


65545 PLATE, TRANSOM Mercruiser 00014332, 2140208, 2165208, 2250507 PLATE
65545 PLATE, TRANSOM Mercruiser
Rating:
68

Buy PLATE, TRANSOM 65545 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Mercruiser entire parts catalog list:

00014332 1982
2140208 1978,1979,1980,1981,1982
2165208 1978
2250507 1977

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03003219
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Position the spring for oil control ring (3) into the oil ring groove in piston (4). The central wire must be located inside the end of the spring.
Position the oil control ring with the word "TOP" in the upward position. Use Tooling (B) to install oil control ring (3) over the piston and the spring. Note: Ensure that the central wire is 180 degrees from the ring gap.
Use Tooling (B) to install intermediate compression ring (2) into the second groove in piston (4). The word "TOP" must be upward.
Use Tooling (B) to install top compression ring (1) into the top groove in piston (4). The word "TOP" must be upward.
Position the piston ring gaps at approximately 120 degrees away from each other. Note: A new piston assembly is supplied with new piston rings.
Illustration 2 g03001779
(A) Cut away for piston cooling jet
(9) Upper shell for connecting rod
(X) Identification marks
(Y) Location tag on connecting rod shells
(Z) Location tag in connecting rod for shells (not shown)
(10) Lower shell for connecting rod cap
Use Illustration 2 as an assembly guide.
Illustration 3 g03001216
Lubricate bushing (8) for piston pin (6) in the connecting rod with clean engine oil. Lubricate the bore for the piston pin in piston (4) with clean engine oil.
Install piston pin (6) to piston (4). Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (A) in order to install circlips (5) to the piston pin bore in piston (4). Note: Ensure that the circlips are seated in the grooves in the piston.
Install upper bearing shell (9) into connecting rod (7). Ensure that the locating tab for the upper bearing shell is correctly seated in slot in the connecting rod.
Install lower bearing shell (10) into connecting rod cap (11). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Temporarily install connecting rod cap (11) and bolts (12) to connecting rod (7) when the assembly is out of the engine. Ensure that the etched number on connecting rod cap matches the etched number on connecting rod. Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side. Tighten bolts (12) to a torque of 20 N m (177 lb in).
Repeat Step 1 through Step 13 for the remaining piston and connecting rod assemblies. Note: Fracture split connecting rods should not be left without the connecting rod caps installed.End By:
Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install" for the correct procedure.


Parts plate Mercruiser:

2057
 
2057 PLATE, BAFFLE-CHOKE HOUSING
01406002, 01407333, 2165203, 2165208
33655
33665
 
33665 PLATE, MOUNTING-BREAKER ASSEMBLY AND CONDENSER
01206002, 01207333, 01326013, 01406002, 01407333, 04706002, 04707333, 04856332, 2165203, 2165208
32435
 
32435 PLATE, FACE - WATER PUMP BASE TO WATER PUMP BODY
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000165CE, 5220200AS, 91331015
2940
 
2940 PLATE ASSEMBLY, COMMUTATOR END
00014332, 01321017, 03301310, 2140208, 2165208, 2250507, 6030000ES
8262
 
8262 PLATE ASSEMBLY, COMMUTATOR END
00014332, 01321017, 03301310, 2140208, 2165208, 5220200AS, 91331015
65550A 2
 
65550A 2 PLATE ASSEMBLY, TRANSOM
00014332, 2140208, 2165208
87057
 
87057 PLATE, CLAMPING-TRIM CYLINDER HOSE
00014332, 2140208, 2165208
Back to top