85060 Mercruiser PLATE, CLAMPING - HYDRAULIC HOSE

Recommended Actions
Table 1
Troubleshooting Test Steps Values Results
1. Check for Leaks in the Engine Oil Cooler
A. Refer to the Testing and Adjusting manual for additional information.
Leaks
Result: A leak was not found in the engine oil cooler.
Proceed to Test Step 2.
Result: A leak is found in the engine oil cooler.
Repair: Perform the following:
1. Install a new oil cooler core. Refer to the Disassembly and Assembly manual for additional information.
2. Flush the cooling system. Refer to the Operation and Maintenance Manual for additional information.
3. Refill the cooling system with the proper coolant. Refer to the Operation and Maintenance Manual for the correct coolant and capacities.
4. Check the oil for coolant. If coolant is found in the oil, drain the crankcase.
5. Refill the crankcase with the proper oil after the leak has been repaired. Refer to the Operation and Maintenance Manual for the correct oil capacities and viscosity.
If the problem is not resolved, proceed to Test Step 2.
2. Check for Leaks in the Power Train Oil Cooler
A. Refer to the Testing and Adjusting manual for additional information.
Leaks
Result: A leak was not found in the power train oil cooler.
Proceed to Test Step 3.
Result: A leak is found in the power train oil cooler.
Repair: Perform the following:
1. Install a new oil cooler core. Refer to the Disassembly and Assembly manual for additional information.
2. Flush the cooling system. Refer to the Operation and Maintenance Manual for additional information.
3. Refill the cooling system with the proper coolant. Refer to the Operation and Maintenance Manual for the correct coolant and capacities.
4. Check the oil for coolant. If coolant is found in the oil, drain the crankcase.
5. Refill the crankcase with the proper oil after the leak has been repaired. Refer to the Operation and Maintenance Manual for the correct oil capacities and viscosity.
If the problem is not resolved, proceed to Test Step 3.
3. Inspect the Water-Cooled Turbocharger
A. Remove the oil drain line from the turbocharger and pressurize the cooling system. Refer to Testing and Adjusting, "Testing the Cooling System" for additional information.
B. Check the turbocharger for coolant leakage.
Turbocharger
Result: The turbocharger is not cracked.
Proceed to Test Step 4.
Result: The turbocharger is cracked.
Repair: Perform the following:
1. Replace the turbocharger. Refer to the Disassembly and Assembly manual for additional information.
2. Flush the cooling system. Refer to the Operation and Maintenance Manual for additional information.
3. Refill the cooling system with the proper coolant. Refer to the Operation and Maintenance Manual for the correct coolant and capacities.
4. Check the oil for coolant. If coolant is found in the oil, drain the crankcase.
5. Refill the crankcase with the proper oil after the leak has been repaired. Refer to the Operation and Maintenance Manual for the correct oil capacities and viscosity.
If the problem is not resolved, proceed to Test Step 4.
4. Inspect the Cylinder Head Gasket
A. Remove the cylinder head. Refer to the Disassembly and Assembly manual for additional information.
B. Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner Projection" for additional information.
Damage
Result: The cylinder head gasket and water seals are not leaking.
Proceed to Test Step 5.
Result: The cylinder head gasket and/or water seals are leaking.
Repair: Install a new cylinder head gasket and new water seals in the spacer plate. Refer to the Disassembly and Assembly manual for additional information.
If the problem is not resolved, proceed to Test Step 5.
5. Inspect the Cylinder Head
A. Perform a leak test on the cylinder head. Refer to the System Operation/Testing and Adjusting manual for additional information.
Crack
Result: A crack is not found in the cylinder head.
Proceed to Test Step 6.
Result: A crack is found in the cylinder head.
Repair: Repair or replace the cylinder head. Refer to the Disassembly and Assembly manual for additional information.
If the problem is not resolved, proceed to Test Step 6.
6. Inspect the Cylinder Liner
A. Inspect the cylinder liner for cracks.
Crack
Result: A crack is not found in the cylinder liner.
Proceed to Test Step 7.
Result: A crack is found in the cylinder liner.
Repair: Replace any cracked cylinder liners. Refer to the Disassembly and Assembly manual for additional information.
If the problem is not resolved, proceed to Test Step 7.
7. Inspect the Cylinder Block
A. Inspect the cylinder block for cracks.
Crack
Result: A crack is found in the cylinder block or cylinder liner.
Repair: Repair or replace the cylinder block. Inspect the top deck. Refer to the Reuse and Salvage Guidelines manual for additional information.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).