811537 Mercruiser PLUNGER KIT, Pump


811537 PLUNGER KIT, Pump Mercruiser 02602347, 02608427, 257B021JS, 4211015L1, 4350100KS, 443B0002S, 443B1003S, 443B100JS, 443HC00JT, 457B100KS PLUNGER
811537 PLUNGER KIT, Pump Mercruiser
Rating:
103

Buy PLUNGER KIT, Pump 811537 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$33.98
 

04-05-2022

-: -
811537 Slider Coil 5 Wheel 4 1/2 Ft.
811537 Slider Coil 5 Wheel 4 1/2 Ft.
$21.39
 

14-06-2021
1.0[0.45] Pounds
-: -
Parker Slider Coil, 5 Wheel, 4 1/2 ft.
Auto & Truck Maintenance || Country of manufacture: Mexico || Manufacturer: PARKER
$43.99
 

11-06-2024
0.31[0.14] pounds
US: Wholesale Marine
New Mercury Mercruiser Quicksilver Oem Part # 811537 Plunger-Pump
MERCURY MARINE
Number on catalog scheme: 7
 

Mercruiser entire parts catalog list:

02602347 1987,1988,1989,1990,1991,1992,1993,1994,1995
02608427 1987
257B021JS 1996,1997
4211015L1 1998
4350100KS 1997
443B0002S 1992,1993
443B1003S 1993,1994,1995
443B100JS 1996
443HC00JT 1996,1997
457B100KS 1997

Information:

Start By:a. remove oil pump1. Check the connecting rods and caps for their identification and location. 2. Turn the crankshaft until the connecting rod caps are in position.3. Remove two bolts (1) and the cap from the connecting rod. Remove the lower half of the bearing from the cap.4. Push the connecting rod away from the crankshaft. Remove the upper half of the bearing from the connecting rod. Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly.5. Install the upper half of the bearing in the connecting rod.6. Pull the connecting rod slowly on to the crankshaft.7. Install the lower half of the bearing in the cap. Be sure the tabs in the back of bearings are in the tab grooves of the connecting rod and cap.The serviceman must be very careful to use Plastigage, Tool (A) correctly. The following points must be remembered:Make sure that the backs of the bearings and the bores are clean and dry.Make sure that the bearing locking tabs are properly seated in their slots.The crankshaft must be free of oil where the Plastigage touches it.Put a piece of Plastigage (A) on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.Do not turn the crankshaft with the Plastigage installed.Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004 in) the readings may be low by 0.013 to 0.025 mm (.0005 to .0010 in). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider that the other.For complete details concerning measuring bearing clearance, see the topic, "Engine Bearings & Crankshafts", SEBD0531. 8. Use Plastigage (A) to check the bearing clearance.9. Put Plastigage (A) on the bearing.10. Put 2P2506 Thread Lubricant on the threads of the rod bolts and seat surfaces of the nuts. Be sure the cylinder numbers on the rod cap and rod are the same and are on the same side of connecting rod. Numbers are on the same side of the rod and cap as are the bearing tab slots. If new rods are installed, put the cylinder number on the rod and cap. Do not turn the crankshaft when Plastigage (A) is in position. 11. Install rod caps (2). Install the two bolts. Tighten each bolt to a torque of 90 8 N m (67 6 lb ft). Put a mark on the nuts and cap, and tighten the nuts an extra 90° 5° from the mark. Remove the rod cap. Remove Plastigage (A), and check the bearing clearance. The bearing clearance must be 0.071 to 0.168 mm (.0028 to .0066 in) for new bearings. Maximum clearance with used bearings is 0.25 mm (.010 in).12. Put clean engine oil on lower half of the bearing. Install the rod cap again. Tighten each nut to a torque of 90 8 N m (67 6 lb ft). Put a mark on the nuts and cap, and tighten the nuts an extra 90 5 degrees from mark.13. Do Steps 1 through 12 for the remainder of the connecting rod bearings.End By:a. install oil pump


Parts plunger Mercruiser:

33317
 
33317 PLUNGER, SHIFT LEVER - SOLENOID SWITCH
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 06661346, 07711346, 08986342, 08987343, 228801, 260801, 3000
808701
 
808701 PLUNGER KIT, Accelerator Pump
02602347, 02608427, 44541101S, 4454110GE, 4454110JT, 45021102S
Back to top