811641 Mercruiser POLE PIECE


811641 POLE PIECE Mercruiser 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS, 4350104JS, 4350104KS, 4350111HS, 4350118JS, 4350118KS, 4441027LE, 444106AM1, 4454118JT, 4502111FE, 4542067LS, 457B101JS, 457B101KS, 457B111GS, 457L101JS, 4652027L POLE
811641 POLE PIECE Mercruiser
Rating:
13

Buy POLE PIECE 811641 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$50.60

28-02-2025

CN: YAJIE-6666
KJWPYNF Car Wheel Spacers Adapter 4pcs Car Aluminum Hub Rings Hub Centric Ring Wheel Bore 56.1-54.1 56.6-54.1 57.1-54.1 60.1-54.1 64.1-54.1 81.1-64.1 108.1-95.3mm
KJWPYNF ✔ High Quality: aluminum alloy with anodized and heat-treated surfaces to enhance corrosion resistance || ✔ Improve Vehicle Stability: wheel spacers widen your vehicle wheel base so as to increase the smoothness of the vehicle make the turning more flexible and prevent the phenomenon of overturning || ✔it is also a necessary product for modified car, which can highlight the tires of the concave body make it full and the body will appear more fashionable || ✔Wheel spacers are an easy install that have a big effect on your ride There aren’t many other aftermarket mods that make this much difference per dollar. || ✔ Before purchasing these wheel spacers, please recheck your vehicle compatibility (year/make/model) in the product description If you have any questions, please send us an email for consultation.
$31.48

28-02-2025
0.6613[0.30] Pounds
CN: DAMUCMSM STORE
Hub Center Ring 4pcs Car Aluminum Hub Rings Hub Center Wheel Bore 56.1-54.1 56.6-54.1 57.1-54.1 60.1-54.1 64.1-54.1 81.1-64.1 108.1-95.3mm Car Wheel Center Bore(81.1-64.1 mm)
CPAMORTEL · The wheel hub is made of high-quality materials, processed by CNC, with a beautiful appearance and corrosion resistance. || · The center ring of aluminum alloy wheels is designed to correct smaller wheel and hub sizes. || · It is made of aluminum alloy and will not melt even under driving conditions. || · Avoid vibration caused by incorrect alignment between the wheels and the vehicle hub. || · Placement on the vehicle: left, right, front, rear.
$42.57
 

10-08-2024
1.1023[0.50] pounds
CN: WELANSM STORE
SDHJKEI Wheel Bore Center Spacer 4pcs Car Aluminum Hub Rings Hub Centric Wheel Bore 56.1-54.1 56.6-54.1 57.1-54.1 60.1-54.1 64.1-54.1 81.1-64.1 108.1-95.3mm Car Hub Centric Rings(81.1-64.1 mm)
SDHJKEI ◆ Placed on the vehicle: left, right, front, rear. || ◆ The center ring of the wheel hub is made of high-quality 6061 aluminum alloy, CNC machined, beautiful and corrosion-resistant. || ◆ The hub center ring is designed to correct smaller wheel and hub sizes. || ◆ Made of aluminum alloy, it will not melt even under driving conditions. || ◆ Eliminate vibrations caused by incorrect wheel alignment.
Number on catalog scheme: 8
 

Mercruiser entire parts catalog list:

4111021L1 1998
4111021TS 1998
4111021UT 1998
4111021UU 1998
411102KN2 1998
41510P1UE 1998
430B00001 1990,1991,1992,1993,1994,1995
430L000JS 1996,1997
4350104JS 1996
4350104KS 1997
4350111HS 1995
4350118JS 1996
4350118KS 1997
4441027LE 1998
444106AM1 1998
4454118JT 1996,1997
4502111FE 1993,1994,1995,1996
4542067LS 1998
457B101JS 1996
457B101KS 1997
457B111GS 1994,1995
457L101JS 1996
4652027LE 1998
4652027M1 1998
4652227MW 1998
474L111JS 1996,1997
474L118JS 1996
474L118JT 1996,1997
4M31027LS 1998

Information:

1. Remove four bolts (1) and the washers from the rocker shaft.2. Remove rocker shaft (2) from the cylinder head.3. Remove push rods (3) from the engine.Install Rocker Shaft Assembly And Push Rods
1. Loosen adjusting screws (4) on the rocker arms for valve clearance. This will prevent a bent valve or push rod at installation.2. Install push rods (3) as shown.3. Put rocker shaft (2) in position on the cylinder head.4. Put 5P3931 Anti-Seize Compound on the threads of the bolts (except the rear bolt flywheel end) that holds the rocker shaft in position. Install the four bolts and washers. Make sure the rocker arms are on all of the push rods.
The dowels on each end of the rocker shaft assembly must make an alignment with the holes in the cylinder head assembly. If the dowels and holes are not in alignment when the rocker shaft assembly is tightened, damage to the rocker shaft assembly will be the result.
5. Tighten the bolts for the rocker shaft as follows:a. Tighten bolts in number sequence to a torque of 155 N m (115 lb.ft.).b. Tighten bolts again in number sequence to a torque of 250 17 N m (185 13 lb.ft.).c. Tighten bolts again and for the last time in number sequence (hand tighten only) to a torque of 250 17 N m (185 13 lb.ft.). 6. The assembled length of springs (5) at both ends of the rocker shaft must be 1.50 0.25 mm (.059 .010 in.). Remove or install the washers behind springs to change the assembled length of the springs.7. Make adjustments until the intake valve clearance is 0.38 mm (.015 in.) and the exhaust valve clearance is 0.64 mm (.025 in.). See the Topic, Engine Valve Lash as shown in the Maintenance Guide. Tighten the locknuts for the adjusting screws to a torque of 29 7 N m (21 5 lb.ft.).end By:a. install valve coverRocker Shaft Assembly, Disassemble And Assemble
Start By:a. remove rocker shaft assembly and push rods 1. Remove O-ring seal (1) from the rear support bracket. A replacement of the O-ring seal must be made each time the head bolt is removed from the rear support bracket. 2. Remove retainer ring (6), washer (5), spring (4) and washers (3) from each end of the rocker shaft. Make a note of the number of washers (3) used at each end of the shaft. Remove rocker arms (2) from each end of the rocker shaft. All the rocker arms, springs, washers and brackets, except the rear support bracket, can be removed from the shaft. 3. Remove the pin from the rear support bracket with a hammer and punch. Remove rear support bracket (7) from the shaft.4. Remove remainder of the rocker arms, springs, washers and brackets from the shaft.5. Remove the plugs from each end of the shaft if necessary. The following steps are for the assembly of the rocker shaft assembly. 6. Install rocker arms (12), brackets (8), washers (11) and springs (9) on the rocker shaft.7. Install rear support bracket (7) on the rocker shaft. Make sure the hole in the rear support bracket is in alignment with the hole in the rocker shaft.8. Put pin (10) in position in the bracket. 9. Install pin (10) through the bracket and shaft with a hammer.10. Pin (10) must extend 9.60 mm (.378 in.) above the bracket. 11. Install O-ring seal (1) in the rear support bracket. Install rocker arm (2) the original number of washers, the spring, the washer and the retainer ring on the rocker shaft.12. Install the front support, rocker arm, original number of washers, the spring, the washer and the retainer ring on the rocker shaft.13. Install the plugs in each end of the rocker shaft, if they were removed.End By:a. install rocker shaft assembly and push rods


Back to top