855383 Mercruiser PRESSURE PIPES ASSEMBLY


855383 PRESSURE PIPES ASSEMBLY Mercruiser 40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND PRESSURE
855383 PRESSURE PIPES ASSEMBLY Mercruiser
Rating:
43

Buy PRESSURE PIPES ASSEMBLY 855383 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$287.83
 

02-12-2023
0.3747[0.17] pounds
US: Boating Accessories
MERCURY PIPES-INJECTOR
MERCURY
Number on catalog scheme: 7
 

Mercruiser entire parts catalog list:

Information:

Start By:a. remove valve covers 1. Remove fuel line (2) with Tool (B). Put protective caps on all fuel openings.2. Make a separation between rocker arm (1) and the push rod with Tool (A). Put identification on each valve bridge as to its location. Remove valve bridges (3). 3. Disconnect fuel lines (4) from fuel line adapters (5). Remove locks (6). Remove adapters (5).4. Remove bolts (8) that hold the rocker shaft assembly (7) to the cylinder head. Remove rocker shaft assembly (7).Install Rocker Shaft Assembly
1. Put rocker shaft assembly (2) into position on the head.2. Put clean engine oil on the threads of bolts (1) and install the bolts to hold rocker shaft assembly. Tighten the bolts as follows:a. Tighten bolts 1 through 6 in number sequence shown to a torque of 270 25 N m (200 20 lb ft).b. Tighten bolts 1 through 6 in number sequence again to a torque of 447 20 N m (330 15 lb ft).c. Tighten bolts 1 through 6 in number sequence shown again to a torque of 447 20 N m (330 15 lb ft). 3. Put clean engine oil on the O-ring for adapter (5). Install adapters (5) and locks.4. Connect fuel lines (3) to adapters (5). Tighten fuel line nuts to 40 7 N m (30 5 lb ft) with Tool (B).5. Put clean engine oil on the valve bridge dowels. Install valve bridges (7) in their correct locations on the cylinder head. Adjustment of the bridge is necessary only if valve grinding or other reconditioning of the cylinder head has been done. See Bridge Adjustment in Testing and Adjusting for this procedure.6. Put clean engine oil on the valve bridges. Make connection between the rocker arms (4) and push rods with Tool (A).7. Make an adjustment of the valve to have a clearance of .038 mm (.015 in) for intake and 0.76 mm (.030 in) for exhaust. See Valve Clearance Setting in Testing and Adjusting.8. Install the fuel line to fuel valves (6). Tighten the fuel line nuts to 40 7 N m (30 5 lb ft) with Tool (B).Disassemble Rocker Shaft Assembly
Start By:a. remove rocker shaft assembly 1. Remove retainer (1) from the shaft.2. Remove the washers and rocker arm (2). 3. Use Tool (A) to remove the pin that holds the bracket (3) to the rocker arm shaft.4. Remove bracket (3), rocker arm (4) and the spring.5. Remove the remainder of the rocker arms. The center brackets do not have pins.Assemble Rocker Shaft Assembly
Make sure all parts of the rocker shaft assembly are clean before installation. 1. Put clean engine oil on shaft (3).2. Install the center springs, rocker arms and bracket.3. Install spring (1), rocker arm (4) and bracket (2).4. Put tape around the shaft on each side of bracket (2) as shown. Put the hole in bracket (2) in alignment with the hole in shaft (3). Put a mark on each piece of tape in alignment with the hole in bracket (2).5. Install pin (5) until it is extended 8.6 m (.34 in) above the surface of bracket (2). Make sure pin (5) is in alignment with the marks on tape before pin is installed. Remove the tape. 6. Install rocker arm (6), washers (7) and retainer (8). Install enough washers until the end play on each end of the shaft is 0.12 to 1.01 mm (.005 to .040 in).End By:a. install rocker shaft assembly


Parts pressure Mercruiser:

806222 36
 
806222 36 PRESSURE HOSE
02602347, 02608427, 257B021JS, 40420001D, 444236HRS, 457B100KS, 4A72040ND, 4C72040TD, 4C8204DLD, 4M4102LRS
801331242
801331243
801331244
801331245
801331246
801331247
813322
 
813322 PRESSURE DISC
428B116KD, 442B110GD, 442B115KD, 4A72040ND
Back to top