882580 Mercruiser PULLEY, Water Pump

Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     138-7575     Link Bracket     4    
B     138-7575     Link Bracket     2    
C     138-7574     Link Bracket     2    
8T-0652 Bolt     2    
D     137-4370     Load Leveling Beam     1    Start By:
Remove the hood and engine enclosure. Refer to Disassembly and Assembly, "Hood and Engine Enclosure - Remove".
Remove the input drive shaft. Refer to Disassembly and Assembly, SENR5894, "Input Drive Shaft - Remove and Install".
Remove the power train guard. Refer to Disassembly and Assembly, SENR5894, "Power Train Guard (Transmission) - Remove and Install".Note: Move the machine to a smooth, level area in order to properly release the implement hydraulic pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Cap all lines, all hoses, and all tubes and plug all lines, all hoses, and all tubes. This will help to prevent fluid loss and this will help to keep contaminants from entering the system.
At operating temperature the implement hydraulic oil tank is hot and under pressure. Hot oil can cause burns.To prevent possible injury, release the pressure in the implement hydraulic system before hydraulic lines or components are disconnected or removed.
At operating temperature, the steering and brake hydraulic oil tank is hot and under pressure. Hot oil can cause burns.To prevent possible personal injury, release the pressure in the steering and brake hydraulic system before hydraulic lines or components are disconnected or removed.
Effective July 1, 1992 regulations prohibit the venting of any refrigerant into the atmosphere. Refer to Caterpillar publications Service Manuals, SENR3334, SENR5664, and NEDG5065 for the proper procedure, the proper equipment, and the proper tools needed in order to reclaim refrigerant from any Caterpillar equipment.
Personal injury can result from contact with refrigerant.Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.Personal injury or death can result from inhaling refrigerant through a lit cigarette.Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.
Move the machine to a smooth, level surface.
Engage the parking brake.
Drain the oil from the transmission in a suitable container for storage or for disposal. The capacity of the transmission is 169 L (44.6 US gal).
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Drain the implement hydraulic tank in a suitable container for storage or for disposal. The capacity of the implement hydraulic tank is 326 L (85 US gal).
Drain the hydraulic oil tank for the steering and brakes in a suitable container for storage or for disposal. The capacity of the hydraulic oil tank for the steering and brakes is 159 L (41 US gal).
Drain the jacket water cooling system. Drain all fluids in a suitable container for storage or disposal. The capacity of the jacket water cooling system is 204 L (54 US gal).
Drain the Separate Circuit Aftercooler System (SCAC). Drain all fluids in a suitable container for storage or disposal. The capacity of the Separate Circuit Aftercooler System (SCAC) is 86 L (23 US gal).
Recover the air conditioner refrigerant from the air conditioner system. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the correct procedure. Refer to Special Publication, NEDG5065, "Air Conditioning Tools" for the correct tools.