854064 Mercruiser PUSH ROD


854064 PUSH ROD Mercruiser 40280001D, 40280002D, 40420001D, 40420002D, 428B116KD, 442B110GD, 442B115KD, 4A72040ND, 4C72040TD, 4C8204DLD, 4CJ2040ND PUSH
854064 PUSH ROD Mercruiser
Rating:
28

Buy PUSH ROD 854064 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$62.37
 

07-10-2017

Planam: Planam
Planam 854064 "MG 260" Safety Overall Coat, Navy, 64
The coat that does everything||Material: 65 % polyester, 35 % cotton||Shrink-proof to DIN EN ISO 6330
$18.99
 

23-06-2021
0.1873929227[0.00] Pounds
-: -
New Mercury Mercruiser Quicksilver Oem Part # 854064 Push Rod
Number on catalog scheme: 8
 

Mercruiser entire parts catalog list:

40280001D 1998
40280002D 1998
40420001D 1998
40420002D 1998
428B116KD 1997,1998
442B110GD 1994,1995,1996,1998
442B115KD 1997
4A72040ND 1998
4C72040TD 1998
4C8204DLD 1998
4CJ2040ND 1998

Information:

Start By:a. remove flywheel housing1. Remove the nut and washer that holds the yoke to the accessory drive, and remove the yoke.
Typical Example2. Remove the bolts and adapter assembly (3) from the flywheel housing. If necessary, use two 3/8" - 16 NC forcing screws to remove adapter assembly (3). Remove O-ring seal (4) from the adapter assembly.3. Remove the lip-type seal from the adapter assembly.4. If necessary, remove the bearing from adapter assembly (3) with tool (A).5. Remove washer (2) from shaft (1).
Typical Example6. Remove the bolts that hold shaft (1) to gear (5), and remove the shaft.
Typical Example7. Remove gear (5) from the flywheel housing.8. Remove washer (6) from cage assembly (7).
Typical Example9. Remove the bolts and cage assembly (7) from the flywheel housing.10. If necessary, remove two dowels (8) and bearing (9) from the cage assembly.
Typical Example11. Remove the nuts from the studs in shaft (13). Remove the shaft from gear assembly (10).12. Remove washer (11) and O-ring seal (14) from the shaft.13. Remove gear assembly (10) from the flywheel housing.14. If necessary, remove bearing (12) from gear assembly (10) with tool (B).15. Remove the washer from the flywheel housing.Install Accessory Drive (Rear)
1. Install the washer (11). Make sure the washer is installed with the small dowel hole toward the top of the flywheel housing.2. If bearing (12) was removed from gear (10), use tooling (A) to install a new bearing (12). Install bearing (12) until it is 1.0 0.5 mm (.04 .02 in.) below the surface of the small gear. The inside diameter of bearing (12) must measure 94.000 0.055 mm (3.7007 .0022 in.) after installation.3. Install gear (10) in the flywheel housing. The small diameter of gear (10) should face toward the flywheel.4. Put O-ring seal (14) and washer (11) in position on shaft (13). Put clean engine oil on the O-ring seal. Tighten the studs in shaft (13) to a torque of 100 15 N m (75 11 lb. ft.).5. Position shaft (13) into gear (10) and the flywheel housing.6. Put 5P3413 Pipe Sealant on the nut end of the studs in shaft (13). Install the washers and nuts to hold the shaft in place. Tighten the nuts to a torque of 220 25 N m (160 18 lb. ft.). 7. If bearing (9) was removed from cage assembly (7), align the lubrication holes in bearing (9) and assembly (7). Use tooling (B) to install bearing (9). Install bearing (9) until it is 1.0 0.5 mm (.04 .02 in.) below the surface of cage assembly (7). The inside diameter of bearing (9) must measure 63.500 0.038 mm (2.5000 .0014 in.) after installation.8. If dowels (8) were removed from the cage assembly, install dowels (8) 3.5 0.5 mm (.14 .02 in.) above the surface of cage assembly (7).9. Position cage assembly (7) and install the bolts. 10. Put washer (6) in position on the dowels in cage assembly (7). 11. Install gear (5) in the flywheel housing. 12. Put shaft (1) in position in gear (5), and install the bolts that hold the shaft to the gear. Tighten the bolts to a torque of 90 15 N m (65 11 lb. ft.). 13. If the bearing was removed from adapter assembly (3), use tooling (A) to install a new bearing. Install the bearing 1.0 0.5 mm (.04 .02 in.) below surface (X). The inside diameter of the bearing must be 63.500 0.038 (2.5000 .0014 in.) after installation.14. Use tool (B) to install the seal in adapter assembly (3). The lip of the seal should face toward the bearing in adapter assembly (3).15. Put O-ring seal (4) in position on adapter assembly (3). Use clean engine oil to lubricate O-ring seal (4) and the lip of the seal in adapter assembly (3).16. Put adapter assembly (3) in position on the flywheel housing and install the bolts that hold it.17. Install the yoke onto shaft (11). Tighten the nut holding the yoke to a torque of 600 50 N m (440 37 lb. ft.).End by:a. install flywheel housing


Back to top