818169T Mercruiser REMOVAL TOOL, Sleeve


818169T REMOVAL TOOL, Sleeve Mercruiser 5120150R1, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910TP, 5E31910TS, 5E32200TP, 5E32900TS, 5E36200TP, 5E36200TS, 5E36210T REMOVAL
818169T REMOVAL TOOL, Sleeve Mercruiser
Rating:
53

Buy REMOVAL TOOL, Sleeve 818169T Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: -
 

Mercruiser entire parts catalog list:

5120150R1 1998
5231100LP 1998
5231100TP 1998
5232100N1 1998
5232100TP 1998
5E31200N1 1998
5E31200TP 1998
5E31200TS 1998
5E31210TP 1998
5E31210TS 1998
5E31800TP 1998
5E31800TS 1998
5E31810TP 1998
5E31810TS 1998
5E31900TP 1998
5E31900TS 1998
5E31910TP 1998
5E31910TS 1998
5E32200TP 1998
5E32900TS 1998
5E36200TP 1998
5E36200TS 1998
5E36210TP 1998
5E36210TS 1998
5E36800TP 1998
5E36800TS 1998
5E36810TP 1998
5E36810TS 1998
5E36900TS 1998
5E36910TP 1998
5E36910TS 1998
5H41400TP 1998
5H41410TP 1998
5H41410TS 1998
5H41600TP 1998
5H41610TP 1998
5H41610TS 1998
5H42300TP 1998
5H42300TS 1998
5H42400TS 1998
5M41400TP 1998
5M41400TS 1998
5M42300TP 1998
5M42300TS 1998
5T32300TP 1998
5T32300TS 1998
5X32200TS 1998
6211001N1 1998
6311002NZ 1998
6315001N1 1998
6315002NZ 1998
6416003N2 1998
6511102N1 1998
6811001N1 1998

Information:


Table 1
Diagnostic Codes Table    
Code and Description    Conditions which Generate this Code    System Response    
268-2 Programmed Parameter Fault erratic, intermittent, or incorrect     The engine's Electronic Control Module (ECM) detects that one or more of the programmable parameters have not been programmed.     The ECM will set the unprogrammed parameter(s) to a default value.
The code is logged.    If the 268-02 diagnostic code is active, program the missing parameter.System configuration parameters are parameters that affect emissions, power of the engine, and machine applications. Default values for the parameters are programmed at the factory. Some parameters may be changed by the customer in order to suit the needs of the specific application. You must reprogram the system configuration parameters if the ECM is replaced and/or if you reprogram the engine rating. Values for these parameters are available on Caterpillar Electronic Technician (ET). Certain configuration parameters are also stamped on the engine information plate.Parameter Descriptions
"Equipment ID"
The "Equipment ID" parameter allows the customer to enter a description into the ECM in order to identify the machine. A maximum of 17 characters can be entered in the field."Engine Serial Number"
Program the "Engine Serial Number" to match the engine serial number that is stamped on the engine information plate. The engine serial number is not preprogrammed on a replacement ECM."FLS" (Full Load Setting)
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information plate. Only change this value if the engine is rerated or if a new ECM is installed. The parameter allows one time of programming without a factory password. In order to change the "FLS" after the initial programming, factory passwords are required."FTS" (Full Torque Setting)
"FTS" is similar to "FLS". Only change this value if the engine is rerated or if a new ECM is installed. Factory passwords are required. A new ECM or a blank ECM allows one time of programming of the "FTS" without the use of factory passwords. In order to change the "FTS" after the initial programming, factory passwords are required.Parameter Table
Table 2
System Configuration Parameters    
Parameter    Available Range or Options    Default    Required Password    
"Equipment ID"     17 characters     N/A     None    
"Engine Serial Number"     8 characters     N/A     None    
ECM Part Number                
ECM Serial Number                
"FLS"     -128 to +127     0     Factory    
"FTS"     -128 to +127     0     Factory    
"Software Group Part Number"                
"Software Group Release Date"                
"Software Group Description"                Parameter Worksheet
Record the following information before you change any programmable parameter.
Table 3
Information from ECM    
"Equipment ID"    
   
"Engine Serial Number"    
   
ECM Part Number        
"ECM Serial Number"    
   
"FLS"    
   
"FTS"    
   
"Software Group Part Number"    
   
"Software Group Release Date"    
   
"Software Group Description"    
   
"Total Tattletale"    
   
Injector Code 1        
Injector Code 2        
Injector Code 3        
Injector Code 4        
Injector Code 5        
Injector Code 6        


Parts removal Mercruiser:

17273
 
17273 REMOVAL TOOL, Bearing
5120136JS, 5120150R1, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910TP, 5E31910TS, 5E32200TP, 5E32900TS, 5E36200TP, 5E36200T
37292
 
37292 REMOVAL/INSTALLTION TOOL, Roller Bearing
5111200LP, 5120136JS, 5120150R1, 5231100LP, 5231100TP, 5232100N1, 5232100TP, 5E31200N1, 5E31200TP, 5E31200TS, 5E31210TP, 5E31210TS, 5E31800TP, 5E31800TS, 5E31810TP, 5E31810TS, 5E31900TP, 5E31900TS, 5E31910TP, 5E31910TS, 5E32200TP, 5E32900TS, 5E36200T
Back to top