17341 Mercruiser RESTRICTOR


17341 RESTRICTOR Mercruiser 01751347, 02602347, 02608427, 257B021JS, 40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 4332087N1, 4350100KS, 4350104JS, 4350104KS, 4350111HS, RESTRICTOR
17341 RESTRICTOR Mercruiser
Rating:
98

Buy RESTRICTOR 17341 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Mercruiser entire parts catalog list:

01751347 1987,1988,1989,1990,1991,1992
02602347 1987,1988,1989,1990,1991,1992,1993,1994,1995
02608427 1987
257B021JS 1996,1997
40430002S 1998
40500006T 1998
40500010T 1998
40500010U 1998
40500120U 1998
4211025RS 1998
4211025TS 1998
4211025TT 1998
4211025US 1998
4211025UU 1998
424106LRS 1998
424106LTT 1998
424106LUS 1998
424106PUU 1998
4332087N1 1998
4350100KS 1997
4350104JS 1996
4350104KS 1997
4350111HS 1995
4350118JS 1996
4350118KS 1997
443B0002S 1992,1993
4441027LE 1998
444106AM1 1998
444106LPS 1998
444236HRS 1998
457B100KS 1997
457B101JS 1996
457B101KS 1997
457B111GS 1994,1995
457L101JS 1996
4M11025LS 1998
4M11025RS 1998
4M11025TS 1998
4M11025TT 1998
4M11025US 1998
4M31027LS 1998
4M4102LPS 1998
4M4102LRS 1998
4M4102LTS 1998
4R42027N1 1998

Information:

1. Remove the alternator belts from pulley (1). Refer to topic "Remove Alternator" in this module for further information.2. Remove bolts (3), Remove pulley (1) from the drive shaft.3. Remove bolts (2). Use two 1/2" - 13 NC forcing screws to remove adapter assembly (4) from the rear of the front drive housing. 4. Remove bolts (5) and accessory drive (6) from the front drive housing.Install Accessory Drive (Front)
1. Make sure the O-ring seals are in position on accessory drive (6). Lubricate the O-ring seals with clean engine oil.2. Install accessory drive (6) in the front drive housing. Make sure the gear teeth of accessory drive (6) are engaged correctly with the teeth of the gear in the front housing. Install bolts (5). 3. Make sure the two O-ring seals are installed on adapter assembly (4). Lubricate the O-ring seals, lip seal and bearings of adapter assembly (4) with clean engine oil. Install adapter assembly (4) and bolts (2). 4. Put pulley (1) in position. Install bolts (3).5. Install the alternator belts on the pulley. Refer to the topic "Install Alternator" in this module for further information.End By:a. install oil pumpb. install fuel control modulec. install water pumpDisassemble Accessory Drive (Front)
Start By:a. remove accessory drive (front) 1. Remove O-ring seals (2) and (3) from adapter (1). 2. Remove seal (4) from adapter (1). Use a press and tool group (A) to remove bearing (5) from adapter (1). 3. Remove bolts (7) to remove gear (8) from shaft (6). Later models have two retainer washers.4. Remove bolts (9) and the retainer washer to remove shaft (6) from adapter (10). 5. Remove O-ring seals (12) and (13) from adapter (10).6. Use a press and tool group (A) to remove bearing (11) from adapter (10).Assemble Accessory Drive (Front)
1. Align the oil hole in the bearing and the oil hole in adapter (1). Use a press and tool group (A), and install the bearing in adapter (1). Check the bore in the bearing after assembly. The bore in the bearing must be 75.000 0.055 mm (2.9528 .0022 in.).2. Install the two O-ring seals in adapter (1). Later models have two retainer washers (2).3. Put clean engine oil on the bearing, and install shaft (3) in adapter (1). Install retainer washer (2) to hold the shaft and adapter together. 4. Put gear (4) in position on shaft (3), and install the bolts to hold them together. 5. Align the oil hole in the bearing and the oil hole in adapter (5). Use a press and tool group (A), and install the bearing in adapter (5). Check the bore in the bearing after assembly. The bore in the bearing must be 75.000 0.055 mm (2.9528 .0022 in.).6. Use tool group (A) to install the seal in adapter (5). Make sure the lip of the seal is toward the bearing as shown. 7. Install O-ring seals (6) and (7) on adapter (5), and put clean engine oil on them.End By:a. install accessory drive (front)


Back to top