808267 RETAINING RING Mercruiser
473B1F0GS
RETAINING
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$96.20
07-10-2017
.25[0.00] pounds
Winderosa: Winderosa
Winderosa 808267 Complete Engine Gasket Kit
Fits: Honda CRF450R 2002 - 2006||Includes every gasket and O-ring required to Rebuild a motor; valve seals, head, base, exhaust, clutch, ignition, and other misc. Gaskets/O-rings (formed rubber valve cover gasket not included)||Winderosa complete engine gasket Sets are designed for a total Rebuild of the engine and transmission, delivering best-in-class value by offering the right balance of price and performance||Constructed from quality materials that meet or exceed OEM specifications||Made in the USA
Fits: Honda CRF450R 2002 - 2006||Includes every gasket and O-ring required to Rebuild a motor; valve seals, head, base, exhaust, clutch, ignition, and other misc. Gaskets/O-rings (formed rubber valve cover gasket not included)||Winderosa complete engine gasket Sets are designed for a total Rebuild of the engine and transmission, delivering best-in-class value by offering the right balance of price and performance||Constructed from quality materials that meet or exceed OEM specifications||Made in the USA
Number on catalog scheme: 2
Compatible models:
473B1F0GS
Mercruiser
Mercruiser entire parts catalog list:
Information:
2. Turn the crankshaft until two pistons are at bottom center. Remove connecting rod caps (1) from the two connecting rods.3. Put tape or pieces of rubber hose over the threads of the connecting rod bolts. This will prevent damage to the crankshaft during removal of the pistons.
Do not let the connecting rods hit the bottom edge of the cylinder liners or the crankshaft during removal and installation of the pistons.
4. Push the piston and connecting rod away from the crankshaft until the piston rings are above the cylinder liner. Remove the two pistons (2) and the connecting rods from the engine.5. Keep each connecting rod cap with its respective connecting rod and piston. Put identification on each connecting rod as to its location in the engine for use at assembly of the engine.6. Do Steps 2 through 5 for the remainder of the pistons.Install Pistons
1. Turn the crankshaft until the bearing journals for the pistons to be installed are at bottom center.2. Put clean engine oil on the crankshaft journals and on the inside of the cylinder liners. Put clean engine oil on the piston rings and connecting rod bearings.3. Move the piston rings on the piston until the ring openings are approximately 90° apart.
Never install tool (A) (the ring compressor) without the use of the cylinder liner as a guide. Damage to the piston rings can be the result.
TYPICAL EXAMPLE4. Put tool (A) in position on the cylinder liner as shown. Put the connecting rod and piston in position in the same cylinder liner from which it was removed and into the ring compressor. Make sure the "V" mark on the piston is in alignment with the "V" mark on the cylinder block.5. Push the piston into position while the connecting rod is put into position over the crankshaft. 6. Put clean engine oil on bearings, bolt threads and surfaces of the nuts that make contact with the connecting rod caps. Put caps (1) in position on the connecting rods and install the nuts. Tighten the nuts to a torque of 30 3 lb.ft. (40 4 N m). Put a mark on each nut and the end of each bolt. Tighten the nuts 90° more.
When the connecting rod caps are installed, make sure the number on the side of the cap is next to and respective with the number on the side of the connecting rod.
7. Follow Steps 1 through 6 for the installation of the other pistons.end by:a) install oil pumpb) install oil pan platec) install cylinder headDisassemble Pistons
start by:a) remove pistons 1. Remove rings from piston with tool (A). 2. Remove snap ring (3), piston pin (1) and connecting rod (2) from piston.Assemble Pistons
If a replacement of the rod pin bearing is made, use a pin boring machine to make the bearing the correct size. See SPECIFICATIONS. 1. Install rod on piston with bearing tab groove (2) and number identification on the same side as the "V" mark (1) on top of piston.2. Install piston pin and snap rings. 3. When the old pistons are used, clean the piston grooves with tool (A) before installing new rings.4. Install rings on piston with tool (B). The ring openings must be 90° apart.end by: a) install pistons
Do not let the connecting rods hit the bottom edge of the cylinder liners or the crankshaft during removal and installation of the pistons.
4. Push the piston and connecting rod away from the crankshaft until the piston rings are above the cylinder liner. Remove the two pistons (2) and the connecting rods from the engine.5. Keep each connecting rod cap with its respective connecting rod and piston. Put identification on each connecting rod as to its location in the engine for use at assembly of the engine.6. Do Steps 2 through 5 for the remainder of the pistons.Install Pistons
1. Turn the crankshaft until the bearing journals for the pistons to be installed are at bottom center.2. Put clean engine oil on the crankshaft journals and on the inside of the cylinder liners. Put clean engine oil on the piston rings and connecting rod bearings.3. Move the piston rings on the piston until the ring openings are approximately 90° apart.
Never install tool (A) (the ring compressor) without the use of the cylinder liner as a guide. Damage to the piston rings can be the result.
TYPICAL EXAMPLE4. Put tool (A) in position on the cylinder liner as shown. Put the connecting rod and piston in position in the same cylinder liner from which it was removed and into the ring compressor. Make sure the "V" mark on the piston is in alignment with the "V" mark on the cylinder block.5. Push the piston into position while the connecting rod is put into position over the crankshaft. 6. Put clean engine oil on bearings, bolt threads and surfaces of the nuts that make contact with the connecting rod caps. Put caps (1) in position on the connecting rods and install the nuts. Tighten the nuts to a torque of 30 3 lb.ft. (40 4 N m). Put a mark on each nut and the end of each bolt. Tighten the nuts 90° more.
When the connecting rod caps are installed, make sure the number on the side of the cap is next to and respective with the number on the side of the connecting rod.
7. Follow Steps 1 through 6 for the installation of the other pistons.end by:a) install oil pumpb) install oil pan platec) install cylinder headDisassemble Pistons
start by:a) remove pistons 1. Remove rings from piston with tool (A). 2. Remove snap ring (3), piston pin (1) and connecting rod (2) from piston.Assemble Pistons
If a replacement of the rod pin bearing is made, use a pin boring machine to make the bearing the correct size. See SPECIFICATIONS. 1. Install rod on piston with bearing tab groove (2) and number identification on the same side as the "V" mark (1) on top of piston.2. Install piston pin and snap rings. 3. When the old pistons are used, clean the piston grooves with tool (A) before installing new rings.4. Install rings on piston with tool (B). The ring openings must be 90° apart.end by: a) install pistons
Parts retaining Mercruiser:
818944
27290