811591 Mercruiser ROCKER ARM


811591 ROCKER ARM Mercruiser 44541101S, 4454110GE, 4454110JT, 4454118JT, 45021102S, 4502111FE ROCKER
811591 ROCKER ARM Mercruiser
Rating:
8

Buy ROCKER ARM 811591 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$71.95
 

13-04-2024
2.41[1.08] Pounds
US: Race-Driven Inc
Ball Joints fit Can-Am Maverick 1000R XXC 2015-2018 Upper and Lower x4
Race-Driven Race-Driven Upper and Lower Ball Joints || Ball Joints are designed to meet or exceed OEM specifications || Fits: 2015 2016 2017 2018 Can-Am Maverick 1000R XXC
$127.24
 

09-08-2022

-: -
Stirling Front Left Suspension Strut and Coil Spring Assembly Replacement - Fit 2002-2006 Nissan Altima | 811591
Message us with your vehicle VIN# for precise fitment; faster shipping || Proforce Complete Strut Assembly includes Strut, Coil Spring, strut mount, boot, bumper kit, spring seat and isolator || Remove and replace your complete strut assembly in just one piece, fast and efficient || Quality Strut Mount for steering precision and vibration reduction || Engineered for precise ride height retention || Powder coating to fight against rust and corrosion || Free shipping to Canada and USA; No any import charge || 1 year manufacturer warranty; 30 days money back guaranty
$35.76
 

09-08-2022
8.3[3.74] Pounds
-: -
The Hillman Group 811591 Hot Dipped Galvanized Hex Bolt, 3/8-Inch x 4-1/2-Inch, 50-Pack
They Require A Pre-Drilled Hole With Compatible Female Thread || Hex Bolts Feature A Six-Sided Head, Which Is Designed To Be Tightened Using A Wrench Or Drill || Hot Dipped Galavanized || From The Brand Name: The Hillman Group
Number on catalog scheme: 15
 

Mercruiser entire parts catalog list:

44541101S 1991,1992,1993,1994,1995,1996
4454110GE 1995
4454110JT 1996,1997
4454118JT 1996,1997
45021102S 1992,1993
4502111FE 1993,1994,1995,1996

Information:

1. Check each bearing cap (1) for its location on the engine. Each cap has an arrow which is toward the front of the block and a number which gives the location of that cap. Keep each bearing with the correct cap.2. Remove bearing caps No. 2 through No. 4. Remove thrust plates from No. 3 upper bearing.
Be careful not to cause damage to the crankshaft journals when the crankshaft is removed.
3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 5 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 122 kg (270 lb.). 4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface 6.4 0.5 mm (.25 .02 in.).2. Install dowel (2) until it is extended from the surface 4.1 0.5 mm (0.16 0.02 in.). 3. Heat crankshaft gear (3) to a maximum temperature of 232°C (450°F). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2).4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft.
Do not cause damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block. For more detail about installation of main bearings see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS.6. Check the bearing clearance with Plastigage.7. Put clean engine oil on the bolts for caps No. 1 and No. 5. Install No. 1 and No. 5 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block. 8. Install thrust plates (5) for the No. 3 upper main bearing. Install the thrust plates with the side that has the identification "Block Side" toward the cylinder block.9. Put clean oil on the bolts for caps No. 2 through No. 4. Install caps No. 2 through No. 4 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows:a) Tighten the bolts on the tab end of the caps first to a torque of 260 14 N m (190 10 lb.ft.).b) Tighten the bolts on the other end of the caps to a torque of 260 14 N m (190 10 lb.ft.).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. 11. Check the play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.15 to 0.51 mm (0.006 to 0.020 in.). The maximum end play with used thrust plates is 0.89 mm (0.035 in.).END BY:a) install pistonsb) install flywheel housingc) install timing gear coverd) install oil pump


Parts rocker Mercruiser:

811587
ROCKER COVER
811587 ROCKER COVER
44541101S, 4454110GE, 45021102S, 4502111FE, 474L118JS
811590
ROCKER ARM
811590 ROCKER ARM
44541101S, 474L118JS
Back to top