881795 Mercruiser ROCKER ARM-EXHAUST


881795 ROCKER ARM-EXHAUST Mercruiser 442B110GD, 442B115KD ROCKER
881795 ROCKER ARM-EXHAUST Mercruiser
Rating:
8

Buy ROCKER ARM-EXHAUST 881795 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$61.09
 

07-10-2017
.32[0.00] pounds
MERCURY: MERCURY
New Mercury Mercruiser Quicksilver Oem Part # 881795 Rocker Arm-Intake
$4.84
 

07-10-2017
.1[0.00] pounds
The Hillman Group Stainless Steel Hex Cap Screws, 1/2 -13 x 2" (881795)
2pc/bag||Uses a 3/4 In. wrench||Passivated||For use with any outdoor project
Number on catalog scheme: 16
 

Compatible models:

442B110GD   442B115KD   Mercruiser

Mercruiser entire parts catalog list:

442B110GD 1994,1995,1996,1998
442B115KD 1997

Information:

Start By:a. remove crankshaft pulley and vibration damper
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a set. If the old seal is put back on the sleeve, the seal will leak.
1. Remove four bolts (1) from adapter (2), and install two 5/16" - 13 NC forcing screws in the adapter to remove it from the drive housing. 2. Remove O-ring seal (4) and crankshaft seal (3) from adapter (2).
Typical Example3. Install tool (B) in the adapter bore as shown.4. Install tool (A) between tool (B) and wear sleeve (5). Turn tool (A) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this several places around the wear sleeve until the sleeve can be removed from the end of the crankshaft by hand.Install Crankshaft Front Seal And Wear Sleeve
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a unit. If the old seal is put back on the sleeve, the seal will leak.
1. Install adapter (3) on tooling (A) as shown.
If the crankshaft seal and wear sleeve come apart during installation, the seal and sleeve become scrap, and a new seal and sleeve must be used as a replacement.
The front seal and wear sleeve cannot be exchanged with the rear seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals would pump the oil out of the crankcase.2. Put crankshaft seal (2) and wear sleeve (1) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. Install the O-ring seal on adapter (3).3. Install tool (B) over the studs of tooling (A). Install nuts (C), and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter. Do not put engine oil on seal during installation. Lubrication of the seal at installation can be a false indication of leakage at a later time.5. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer. Put 9S3265 Retaining Compound on the outside diameter of the crankshaft and the inside diameter of the wear sleeve.6. Put clean engine oil on the adapter O-ring seal. 7. Install tooling (D) on the end of the crankshaft.8. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft. 9. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).10. Install tooling (B) and (F) as a unit on the guide bolts and over the locator.11. Put clean 1P0808 All Purpose Lubricant on the face of nut (G), and install nut (G) on the locator. Tighten nut (G) until the wear sleeve and adapter are in position.12. Remove the tooling from the engine. 13. Install bolts (4) to hold adapter (3) in position.End By:a. install crankshaft pulley and vibration damper


Parts rocker Mercruiser:

801331742
 
801331742 ROCKER ARM
442B110GD, 442B115KD
801331741
 
801331741 ROCKER ARM
442B110GD, 442B115KD
881793
ROCKER ARM ASSEMBLY
881793 ROCKER ARM ASSEMBLY
442B110GD, 442B115KD
881794
ROCKER ARM-INTAKE
881794 ROCKER ARM-INTAKE
442B110GD, 442B115KD
801763790
801763766
 
801763766 ROCKER COVER (FRONT)
442B110GD, 442B115KD
854057
 
854057 ROCKER ARM ASSEMBLY
40420001D, 428B116KD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND
854059
 
854059 ROCKER ARM (INTAKE)
428B116KD, 442B115KD, 4A72040ND, 4C8204DLD, 4CJ2040ND
Back to top