811636 Mercruiser ROTOR


811636 ROTOR Mercruiser 4111021L1, 430B00001, 430L000JS ROTOR
811636 ROTOR Mercruiser
Rating:
88

Buy ROTOR 811636 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$125.00

12-12-2024

US: Midnight marine
Mercruiser 3.0L / LX OEM Service Kit Alpha One Gen 2/Delco EST IGN: Fuel & Oil Filter, Alpha Impeller Kit, Distributor Cap/Rotor, Spark Plugs, & Wires Bayliner SeaRay Larson
Midnight Marine Have questions about fitment??? Just provide us with your engine serial number. Midnight Marine delivers high-quality, affordable OEM Mercruiser maintenance kits right to your door in one convenient package. || Oil Filter 866340Q03 (14957) Fuel Filter Kit 8M0046752 (11004a 803897) Water Pump Impeller Alpha One Gen 8M0100526 (8M0100527) Delco EST Ignition distributor Cap(811635) & Rotor(811636) Kit 811635Q2 Wire set 816761Q14 816336 (4) OEM AC Spark Plugs MR43LTS (810883) || Midnight Marine Service Kit (1991+ Mercruiser 3.0L / Lx (carb) motor w/ Delco EST distributor)
$53.98
 

26-05-2023
0.08[0.04] Pounds
-: -
Vertex 811636 Complete Gasket Set
These sets include all gaskets and seals necessary to rebuild the engine and transmission.
$7.13
 

26-08-2024
0.3[0.14] pounds
Amazon.com
Walker Products 926-1007 Distributor Rotor
Walker Products Walker Products Distributor Cap is professionally manufactured for premium aftermarket replacement || Walker Distributor Cap is OE fit, form and function || OE Replacement: 10467546 10495411 D450 811636 8104954110 10470200 986651 || Please check the Vehicle Application before purcahse
Number on catalog scheme: 3
 

Compatible models:

Mercruiser entire parts catalog list:

4111021L1 1998
430B00001 1990,1991,1992,1993,1994,1995
430L000JS 1996,1997

Information:

Start By:a. remove timing gear cover1. Put the engine in correct timing. See the topic, Remove Fuel Injection Pump Housing and Governor (Earlier) or Remove Fuel Injection Pump Housing And Governor (Later) for this procedure.
Typical Example2. Remove bolt (1) and the washer that holds gear (2) in place.3. Install tooling (C) and bolt (1) to hold the sleeve on the end of the fuel injection pump camshaft.4. Install tooling (A) on gear (2) and tighten the center bolt of tooling (A) until the gear is loosened.5. Remove tooling (A), bolt (1), tooling (C) and the gear.
Typical Example6. Remove bolts (4), plate (3) and idler gear (5). 7. Inspect the bearing in idler gear (5) for wear or damage. If a replacement of the bearing is needed, use tool group (B) and a press to remove it from the gear as shown.
Typical Example8. Remove bolts (6) and camshaft gear (7) from the camshaft.9. Remove the three nuts on the back side of the plate that hold the fuel pump to the plate.
Typical Example10. Bend locks (9) away from the bolts.11. Remove the bolts, locks (9) and plate (8) from the cylinder block.12. Remove the old gasket material from the cylinder block and plate (8).Install Timing Gears And Plate
Typical Example1. Make sure O-ring seal (10) is in place on the fuel pump housing.2. Clean the old gasket from the contact surfaces of the timing gear plate and cylinder block. Install a new gasket on the cylinder block. Cut the gasket even with the bottom face of the cylinder block. Put 5H2471 Gasket Cement on the bottom of the gasket where the gasket makes contact with the gasket for the oil pan.
Typical Example3. Put timing gear plate (8) in position on the cylinder block. Install the three nuts that hold the fuel pump on the back side of the timing gear plate. Install locks (9) and the six bolts that hold the plate in place.
Typical Example4. Install camshaft gear (7) with the "C" mark on the camshaft gear in alignment with the "C" mark on the crankshaft gear. Install the washers and bolts (6) that hold the camshaft gear in place. 5. Install the bearing in idler gear (5) with tool group (B) and a press. The end of the bearing must be 1.52 mm (.060 in.) below the face of the gear hub.
Typical Example6. Put idler gear (5) in position, and install plate (3) and bolts (4) that hold it.
Typical Example7. Put fuel injection pump drive gear (2) in position on the fuel injection pump, and install the bolt and washer that hold it. Install the washer with the larger outside diameter toward the bolt head. Do not tighten the bolt at this time. 8. Install tooling (D) in the holes of the fuel injection pump drive gear as shown. Put a torque of approximately 68 N m (50 lb.ft.) on the pump drive gear in a clockwise direction (as seen from the front of the engine). With the clockwise torque on the pump drive, use tooling (E) to tighten the bolt to a torque of 270 25 N m (200 18 lb.ft.).9. Check timing of the fuel injection pump and engine, see the topic, Timing Check in the Systems Operation, Testing And Adjusting Manual.End By:a. install timing gear cover


Parts rotor Mercruiser:

42775
 
42775 ROTOR (INCLUDES BEARINGS)
00014332, 01207333, 01402414, 01407333, 01751347, 01851333, 01854335, 02287333, 02602347, 02607333, 02608427, 03307332, 03308333, 04544347, 06661346, 07711346, 08987343, 4052110CR, 430B00001, 44541101S, 4454110AS, 45021102S, 474H110AR
813962
 
813962 ROTOR
01207333, 01402414, 01407333, 01751347, 02602347, 02608427, 04544347, 06661346, 4052110CR, 430B00001, 44541101S, 4454110AS, 45021102S, 474H110AR
9089
 
9089 ROTOR
01851333, 430B00001
811872
ROTOR ASSEMBLY
811872 ROTOR ASSEMBLY
02602347, 02608427, 257B021JS, 4111021L1, 411102KN2, 4211015L1, 430B00001, 430L000JS, 4350100KS, 443B0002S, 443B1003S, 443B100JS, 443HC00JT, 44541101S, 4454110GE, 4454110JT, 45021102S, 457B100KS, 4M11025LS
811636 1
ROTOR
811636 1 ROTOR
4111021L1, 4111021TS, 411102KN2
Back to top