20362 Mercruiser BOLT, MOUNTING BRACKET TO EXHAUST MANIFOLD (1 1/2")


20362 BOLT, MOUNTING BRACKET TO EXHAUST MANIFOLD (1 1/2") Mercruiser 01406002, 01407333, 04706002, 04707333, 04856332, 44031854 BOLT
20362 BOLT, MOUNTING BRACKET TO EXHAUST MANIFOLD (1 1/2") Mercruiser
Rating:
103

Buy BOLT, MOUNTING BRACKET TO EXHAUST MANIFOLD (1 1/2") 20362 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

Mercruiser entire parts catalog list:

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     135-7575     Link Bracket     2    Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect" for the machine that is being serviced.
Remove the sweeps. Refer to Disassembly and Assembly, "Sweeps - Remove and Install" for the machine that is being serviced.
Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install" for the machine that is being serviced.
Remove the refrigerant condenser. Refer to Disassembly and Assembly, "Referigerant Condenser - Remove and Install" for the machine that is being serviced. Removal of the inlet line and removal of the outlet line are not necessary.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin. At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Check the coolant level only after the engine has been stopped and the cooling system pressure cap is cool enough to touch with your bare hand.Remove the cooling system pressure cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
The radiator assembly is located at the front of the machine.
Drain the cooling system. Refer to the Operation and Maintenance Manual, SEBU7140, "Cooling System Coolant (DEAC) - Change" for the correct procedure. The capacity of the cooling system is 56 L (14.8 US gal).
Illustration 1 g00583775
Remove two bolts (2) and plate (1). Repeat this step for the remaining plate on the other side of the machine.
Illustration 2 g00583863
Remove eight bolts (3) and hood (4). Use two persons to remove hood (4). The weight of hood (4) is 39 kg (85 lb).
Illustration 3 g00583893
Loosen two clamps (5) and disconnect hose assembly (6) .
Remove baffle (8), tube (7), and hose assembly (6) as one unit. Use two persons to remove baffle (8). The weight of baffle (8) is 20 kg (45 lb).
Illustration 4 g00583896
Remove four bolts (9) and eight bolts (10) .
Remove two-piece guard assembly (11) .
Illustration 5 g00584137
Remove six nuts (13) and fan spider assembly (12). Use two persons to remove fan spider assembly (12). The weight of fan spider assembly (12) is 27 kg (60 lb).
Illustration 6 g00584213
Cut cable straps (16) that secure hose (17) .
Remove sixteen bolts (14) and shroud assembly (15). Use two persons to remove shroud assembly (15). The weight of shroud assembly (15) is 20 kg (45 lb).
Illustration 7 g00584280
Loosen two clamps (18) and remove tube (19) .
Disconnect two transmission oil cooler lines (20) .


Parts bolt Mercruiser:

46717
 
46717 BOLT, CRANKSHAFT BEARING CAP TO CYLINDER BLOCK
01206002, 01207333, 01326013, 01406002, 01407333, 2165203, 2165208
34510
 
34510 BOLT, CYLINDER HEAD TO CYLINDER BLOCK (3 37/64")
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 2165203, 2165208, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
7016
 
7016 BOLT, THRU (3")
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 02287333, 02607333, 03302336, 03307332, 08986342, 228801, 260801, 44031854
33322
 
33322 BOLT, THRU - SLIP RING END FRAME TO DRIVE END FRAME
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 08986342
52269
 
52269 BOLT, CONNECTING ROD BEARING CAP
01406002, 01407333, 430B00001
49105
 
49105 BOLT, CYLINDER HEAD TO CYLINDER BLOCK (4 1/8")
03302336, 03307332, 03308333, 04544347, 06661346, 37011856, 4052110CR, 44031854, 44541101S, 4454110AS, 4454110GE, 4454110JT, 4454118JT, 45021102S, 4502111FE, 474H110AR, 474L111JS, 474L118JS, 474L118JT
49106
 
49106 BOLT, (2.00 Inch), CYLINDER HEAD TO CYLINDER BLOCK
03307332, 03308333, 04544347, 06661346, 37011856, 4052110CR, 44031854, 44541101S, 4454110AS, 4454110GE, 4454110JT, 4454118JT, 45021102S, 4502111FE, 4542067LS, 4652027LE, 4652027M1, 4652227MW, 474H110AR, 474L111JS, 474L118JS, 474L118JT
49101
 
49101 BOLT, PULLEY AND HARMONIC BALANCER
03302336, 03307332, 03308333, 04544347, 37011856, 44031854
Back to top