23296 Mercruiser SCREW, WATER PUMP AND TIMING COVER(2 5/8")


23296 SCREW, WATER PUMP AND TIMING COVER(2 5/8") Mercruiser 2888203 SCREW
23296 SCREW, WATER PUMP AND TIMING COVER(2 5/8") Mercruiser
Rating:
43

Buy SCREW, WATER PUMP AND TIMING COVER(2 5/8") 23296 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 33
 

Compatible models:

2888203   Mercruiser

Mercruiser entire parts catalog list:

2888203 1973,1974,1975,1976,1977

Information:


Table 1
Diagnostic Codes Table    
J1939 Code     CDL Code     Code Description     Comments    
N/A     E1363 (1)     Low Engine Cooling Fan Speed     The code is logged.    
N/A     544-2     Engine Cooling Fan Speed Sensor : Erratic, Intermittent, or Incorrect     The code is logged.    
N/A     544-8     Engine Cooling Fan Speed Sensor : Abnormal Frequency, Pulse Width, or Period     The code is logged.    The engine cooling fan speed sensor provides a signal to the Electronic Control Module (ECM). The ECM controls fan speed by varying the current to the fan control solenoid.The engine cooling fan speed sensor receives a supply voltage of 8.0 0.5 VDC from the ECM. The sensor outputs a frequency that is directly proportional to fan speed. The sensor generates a signal pulse for each revolution of the fan. The output frequency varies between 5 Hz to 180 Hz over the speed range between 50 rpm and 1800 rpm.
Illustration 1 g03011039
Schematic for the fan speed sensor
Table 2
Troubleshooting Test Steps     Values     Results    
1. Check the Status of the Engine Fan Speed
A. Turn the keyswitch to the OFF position.
B. Connect Caterpillar Electronic Technician (ET) to the service tool connector.
C. Turn the keyswitch to the ON position.
D. Access the "Fan Override Test" under the "Diagnostics" menu.
E. Start the "Fan Override Test" on Cat ET. Set the fan speed to 500 rpm.
F. Use a 351-8635 Tachometer Kit to determine the actual speed of the fan.
G. Compare the engine fan speed that is reported by Cat ET to the actual engine fan speed that is reported by the photo-tachometer.
H. Deactivate the "Fan Override Test".
I. Turn the keyswitch to the OFF position.
   
Fan speed    
Result: The engine fan speed is within 50 rpm.
The sensor is operating correctly. There may be an intermittent electrical problem in a connector or in the harness. If an intermittent problem is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect".
Result: The engine fan speed is not within 50 rpm.
Proceed to Test Step 2.    
2. Check the Sensor Supply Voltage at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor connector from the wiring harness.
C. Turn the keyswitch to the ON position.
D. Measure the sensor supply voltage between terminal 2 and terminal 3.
   
Supply voltage    
Result: The supply voltage is reaching the sensor.
Proceed to Test Step 3.
Result: The supply voltage is not reaching the sensor.
Refer to Troubleshooting, "Sensor Supply - Test".
   
3. Check the Signal Frequency at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Remove the wire from terminal 1 on the sensor side of the connector. Connect the sensor connector.
C. Turn the keyswitch to the ON position.
D. Access the "Fan Override Test" under the "Diagnostics" menu on Cat ET.
E. Start the "Fan Override Test" on Cat ET. Set the fan speed to 800 rpm.
F. Use a multimeter to measure the frequency between the signal wire from the sensor and engine ground.
G. Deactivate the "Fan Override Test".
H. Turn the keyswitch to the OFF position.
I. Restore all connectors and wiring to the original configuration.
   
Sensor frequency    
Result: The frequency is approximately 80 Hz.
The engine cooling fan speed sensor is generating the correct signal.
Repair the harness or replace the harness.
Verify that the problem is resolved.
Result: The frequency is not approximately 80 Hz.
Replace the fan drive assembly.
Verify that the problem is resolved.
   Complete the procedure in the order in which the steps are listed.If the procedure corrected the issue, return the engine to service.If the procedure did not correct the issue, Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts screw Mercruiser:

47277
 
47277 SCREW, PULLEY AND HUB TO WATER PUMP (3/4")
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 04856332, 06661346, 07711346, 08986342,
33052
 
33052 SCREW, THROTTLE BODY TO FLOAT BOWL
01206002, 01207333, 01326013, 01406002, 01407333, 04706002, 04707333, 04708004, 04856332, 08986342, 2165203, 2165208, 2888203
33042
 
33042 SCREW, FAST IDLE CAM TO FLOAT BOWL
01206002, 01207333, 01326013, 01406002, 01407333, 04706002, 04707333, 04856332, 08986342, 2165203, 2165208, 2888203
Back to top