39970 Mercruiser SCREW, END CAP/CONNECTOR TO EXHAUST MANIFOLD (7/8")


39970 SCREW, END CAP/CONNECTOR TO EXHAUST MANIFOLD (7/8") Mercruiser 01206002, 01207333, 01326013 SCREW
39970 SCREW, END CAP/CONNECTOR TO EXHAUST MANIFOLD (7/8") Mercruiser
Rating:
58

Buy SCREW, END CAP/CONNECTOR TO EXHAUST MANIFOLD (7/8") 39970 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 22
 

Compatible models:

Mercruiser entire parts catalog list:

Information:


Table 1
J1939 Code and Description Comments
4817-13
Engine Intake Manifold #1 Absolute Pressure : Out of Calibration During key on, the signal voltage from the Intake Manifold pressure sensor indicated an Intake Manifold pressure greater than +/- 15 kPa (2.2 psi) from the Atmospheric Pressure sensor.
Reference sensor : Atmospheric Pressure Sensor
5631-13
Engine Throttle Valve Differential Pressure : Out of Calibration During Key on, the signal voltage from the engine throttle valve differential pressure sensor indicated that the differential pressure detected is greater than 11 kPa (1.6 psi)
There is not a reference for this sensor.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Diagnostic Trouble Codes
A. Establish communication between Cat® Electronic Technician (ET) and the Electronic Control Module (ECM) . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the "Warranty Report" from the engine ECM before troubleshooting or clearing diagnostic trouble codes.
C. Wait at least 30 seconds in order for the diagnostic codes to become active.
Look for an active -13 code or for a logged -13 code.
Diagnostic Trouble Codes
Result: There is an active or there is a logged -13 code.
Proceed to Test Step 2.
2. Check for Debris
A. Turn the keyswitch to the OFF position.
B. Check the suspect sensor for debris.
C. If applicable, check the reference sensor for debris.
D. Check the sensor measurement port for blockage by debris.
E. If debris is found, clear the debris from the measurement port and replace the suspect sensor.
F. Turn the keyswitch to the ON position.
G. Check for -13 codes. Wait at least 30 seconds in order for the diagnostic codes to become active.
Debris
Result: The sensor measurement port is not blocked by debris.
Proceed to Test Step 3.
Result: A -13 code is not present, return the unit to service.
Result: A -13 code is present, replace the suspect sensor. Verify that the problem is resolved.
Result: If more than one -13 code is present and the codes have a reference sensor, replace the reference sensor. Verify that the problem is resolved.
3. Inspect the Suspect Sensor Connector
A. Turn the keyswitch to the OFF position.
Inspect the suspect sensor connector for moisture and/or corrosion.
Moisture
Result: The suspect sensor connector has moisture and/or corrosion.
Proceed to Test Step 4.
Result: The suspect sensor connector does not have moisture and/or corrosion.
Replace the affected sensor.
4. Remove any moisture and/or corrosion
A. Disconnect the suspect sensor connector.
B. Remove any moisture and/or corrosion from the outside of the connector. Check for moisture and corrosion inside the connector. Verify that the seals for the wires are sealing correctly. Refer to Troubleshooting, "Electrical Connectors - Inspect", if necessary.
C. If necessary, repair the connector or replace the connector.
D. Reconnect the connector. Verify that the connection is secure.
E. Turn the keyswitch to the ON position.
F. Monitor the diagnostic codes on Cat ET. Check for -13 codes. Wait at least 30 seconds in order for the diagnostic codes to become active.
Moisture
Result: A -13 code is not present, return the unit to service.
Result: A -13 code is present, replace the suspect sensor. Verify that the problem is resolved.
Result: If more than one -13 code is present and the codes have a reference sensor, replace the reference sensor. Verify that the problem is resolved.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts screw Mercruiser:

33043
 
33043 SCREW, AIR HORN TO FLOAT BOWL (SHORT)
01206002, 01207333, 01326013, 01406002, 01407333, 04706002, 04707333, 04708004, 04856332, 08986342, 2165203, 2165208, 2888203
33648
 
33648 SCREW, MOUNTING PLATE TO PRIMARY HOUSING (3/8")
01206002, 01207333, 01326013, 01406002, 01407333, 2165203, 2165208
31832
 
31832 SCREW, MOUNTING BRACKET TO TRANSOM PLATE
00014332, 01206002, 01207333, 01321017, 01326013, 01406002, 01407333, 02287333, 02607333, 03301310, 03302336, 03307332, 04706002, 04707333, 08986342, 2140208, 2165208, 2250507, 228801, 260801, 30001854, 37011856, 44031854, 5220200AS, 91331015
24963
 
24963 SCREW, SOLENOID SWITCH TO DRIVE END HOUSING
01206002, 01207333, 01326013, 01406002, 01407333, 02287333, 02607333, 03302336, 03307332, 08986342, 228801, 260801
27304
 
27304 SCREW, RETAINER PLATE TO DRIVE END FRAME
01206002, 01207333, 01326013, 01406002, 01407333, 08986342
26065
 
26065 SCREW, WIRING HARNESS CLIP TO COVER PLATE (1")
00014332, 01206002, 01207333, 01326013, 01406002, 01407333, 01701335, 02287333, 02297343, 02607333, 02608427, 04706002, 04707333, 04708004, 04856332, 04881333, 07711346, 08987343, 32001876
813981
 
813981 SCREW
01207333, 01402414, 01407333, 01751347, 02602347, 02608427, 04544347, 06661346, 4052110CR, 430B00001, 44541101S, 4454110AS, 45021102S, 474H110AR
76630
 
76630 SCREW
01207333, 01402414, 01407333, 01751347, 02602347, 02608427, 04544347, 06661346, 4052110CR, 4211015L1, 4262C01JT, 443B0002S, 4454110AS, 474H110AR
Back to top