47220 Mercruiser SCREW, COVER ATTACHING (3/8")


47220 SCREW, COVER ATTACHING (3/8") Mercruiser 03302336, 03307332 SCREW
47220 SCREW, COVER ATTACHING (3/8") Mercruiser
Rating:
78

Buy SCREW, COVER ATTACHING (3/8") 47220 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

Compatible models:

03302336   03307332   Mercruiser

Mercruiser entire parts catalog list:

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
1180-3
Engine Turbocharger 1 Turbine Inlet Temperature : Voltage Above Normal 3908-3
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Voltage Above Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1180-4
Engine Turbocharger 1 Turbine Inlet Temperature : Voltage Below Normal 3908-4
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Voltage Below Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1180-8
Engine Turbocharger 1 Turbine Inlet Temperature : Abnormal Frequency, Pulse Width, or Period 3908-8
Engine Turbocharger #1 Turbine Intake Temperature Sensor : Abnormal Frequency, Pulse Width, or Period If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-3
Engine Turbocharger 2 Turbine Inlet Temperature : Voltage Above Normal 3909-3
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Voltage Above Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-4
Engine Turbocharger 2 Turbine Inlet Temperature : Voltage Below Normal 3909-4
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Voltage Below Normal If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged.
1181-8
Engine Turbocharger 2 Turbine Inlet Temperature : Abnormal Frequency, Pulse Width, or Period 3909-8
Engine Turbocharger #2 Turbine Intake Temperature Sensor : Abnormal Frequency, Pulse Width, or Period If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value of 0 °C (32 °F) is used.
The code is logged. Refer to the application-specific wiring schematic for pin locations.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -3 code is active or logged.
Proceed to Test Step 2.
Result: A -4 code is active or logged.
Proceed to Test Step 3.
Result: A -8 code is active or logged.
Proceed to Test Step 5.
2. Create a Short at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor with the active -3 code.
C. Install the jumper wire between the following terminals at the sensor connector:
- Pin 2 (sensor return) and Pin 3 (sensor signal)
D. Connect Cat ET.
E. Use Cat ET to monitor the following:
- -4 code
F. Turn the keyswitch to the OFF position.
Create a Short
Result: A -4 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
Result: A -4 code did not become active.
Proceed to Test Step 4.
3. Create an Open at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor with the active -4 code.
C. Connect Cat ET.
D. Use Cat ET to monitor the following:
- -3 code
E. Turn the keyswitch to the OFF position.
Create an Open
Result: A -3 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
Result: A -3 code did not become active.
Proceed to Test Step 4.
4. Check the 8 VDC Supply Voltage at the Sensor Connector
A. Turn the keyswitch to the ON position.
B. Measure the voltage at the following pin locations of the affected sensor connector:
- Pin 1 and Pin 2
C. Reconnect the sensor.
Supply Voltage
Result: The supply voltage is approximately 8.0 0.2 VDC
Proceed to Test Step 8.
Result: The supply voltage is not approximately 8.0 0.2 VDC.
Repair: There is a short in the wiring harness to the battery. Repair or replace the wiring harness.
If the problem is not resolved, proceed to Test Step 5.
5. Check the PWM Circuit for an Open
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor with the active -8 code.
C. Disconnect the J2 connector at the Electronic Control Module (ECM).
D. Measure the resistance between the following locations for the sensor:
- Pin 3 (sensor connector) and the appropriate PWM signal wire on the ECM connector
Open


Parts screw Mercruiser:

5087
 
5087 SCREW, DISTRIBUTOR CAP ATTACHING
02287333, 02607333, 03302336, 03307332, 08986342, 228801, 260801, 2888203, 44031854
28635
 
28635 SCREW, WATER TUBE SEALING COVER TO GIMBAL HOUSING (5/8")
00014332, 00019003, 01321017, 01326013, 01701335, 03301310, 03302336, 03307332, 04706002, 04707333, 04708004, 04856332, 04881333, 08986342, 2140208, 2165208, 2250507, 30001854, 32001876, 44031854, 4542067LS, 5000147JS, 5000150DP, 5000165CE, 5111200LP
47461
 
47461 SCREW (1")
01701335, 02287333, 02607333, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 04708004, 04856332, 04881333, 228801, 260801, 37011856, 4052110CR, 4454110AS, 4454118JT, 4502111FE, 4542067LS, 4652027LE, 4652027M1, 4652227MW, 473B116KD, 473B1
40001203
SCREW, PUMP TO BRACKET (45MM) - METRIC
40001203 SCREW, PUMP TO BRACKET (45MM) - METRIC
02287333, 02607333, 03302336, 03307332, 08986342, 228801, 260801, 40430002S, 4211015L1, 4211025RS, 4211025TS, 4211025TT, 4211025US, 4211025UU, 4231017L1, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028U
60685
 
60685 SCREW, BRUSH LEAD TO FIELD FRAME BRUSH
01206002, 01207333, 01326013, 01406002, 01407333, 02287333, 02607333, 03302336, 03307332, 08986342, 228801, 260801
60170
 
60170 SCREW, FLANGE TO PROPELLERE SHAFT (1")
02287333, 02297343, 03302336, 03307332, 04706002, 04707333, 08986342, 228801
68101
 
68101 SCREW, FLYWHEEL HOUSING ATTACHING(R.H. ROTATION)
00014332, 01701335, 01751347, 01851333, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 04544347, 04706002, 04707333, 04708004, 04856332, 04881333, 06661346, 07711346, 08987343, 257B021JS, 40430002S, 40500006T, 40500010T, 405000
93467
 
93467 SCREW, SILENCER ADAPTER (7/8")
02297343, 03307332, 03308333, 04544347
Back to top