48130 Mercruiser SCREW, THERMOSTAT HOUSING (4-1/2")


48130 SCREW, THERMOSTAT HOUSING (4-1/2") Mercruiser 00014332, 01701335, 01751347, 01854335, 02287333, 02602347, 02607333, 02608427, 07711346, 08987343, 4454110AS, 474H110AR SCREW

Buy SCREW, THERMOSTAT HOUSING (4-1/2") 48130 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Mercruiser entire parts catalog list:

00014332 1982
01701335 1985,1986,1987,1988,1989
01751347 1987,1988,1989,1990,1991,1992
01854335 1985,1986
02287333 1983
02602347 1987,1988,1989,1990,1991,1992,1993,1994,1995
02607333 1983
02608427 1987
07711346 1986,1987
08987343 1983,1984,1985,1986,1987
4454110AS 1988,1989,1991,1992
474H110AR 1988,1989,1990,1991

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 2
B - Loctite C5A Copper Anti-Seize -
C -- Loctite 517 Thread Sealant -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01121095Note: Thoroughly clean the spacer plate and the bottom surface of the cylinder head and the top of the cylinder block. A new spacer plate gasket and a cylinder head gasket must be installed when the cylinder head is removed.
Install O-ring seal (15) on the dowel. Install gasket (14).
Install spacer plate (12). Install seals (10) and seals (11). Install O-ring seal (13).
Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner Projection".
Illustration 2 g01120717
Apply Tooling (C) to pipe plug (8). Pipe plug (16) MUST be installed in cylinder head (8).
Apply Tooling (B) to the threads of pipe plug (17).
Install cylinder head gasket (9) on the spacer plate.
Install Tooling (A) and a suitable lifting device on cylinder head (8). The weight of cylinder head (8) is approximately 47 kg (104 lb).
Illustration 3 g01121159
Carefully install cylinder head (8) on the dowel pins on the cylinder block.
Apply Tooling (B) to the threads of bolts (3). Position gasket (2) and install bolts (3). Tighten the bolts to a torque of 50 5 N m (37 4 lb ft).
Coat the threads of bolts (6) and (7) with clean engine oil. Install bolts (6) and (7) according to the instructions in Step 11 and Step 12.Note: Only 254 mm (10 inch) bolts (6) can be used for the following torque procedures.
Illustration 4 g06338934
Tightening sequence with 362-8264 Cylinder Head Gasket (MLS) and 110-6994 Spacer Plate (Aluminum) or 362-9677 Spacer Plate (Aluminum).Note: Refer to Illustration 4 for the correct tightening sequence.
Tighten bolt (1) through bolt (8) to a torque of 30 5 N m (22 4 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 100 15 N m (75 11 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 450 15 N m (332 11 lb ft).
Loosen bolt (1) through bolt (8) an angle of 90 degrees.
Tighten bolt (1) through bolt (8) to a torque of 490 15 N m (361 11 lb ft).
Tighten bolt (9) and bolt (10) to a torque of 55 10 N m (40 7 lb ft).
Illustration 5 g06338934
Tightening sequence with 362-8264 Cylinder Head Gasket (MLS) and 519-7297 Spacer Plate (Iron).Note: Refer to Illustration 5 for the correct tightening sequence.
Tighten bolt (1) through bolt (8) to a torque of 30 5 N m (22 4 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 145 15 N m (107 11 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 145 15 N m (107 11 lb ft).
Turn bolt (1) through bolt (8) an angle of 180 5 degrees.
Tighten bolts (9) and (10) to a torque of 55 10 N m (40 7 lb ft).
Illustration 6 g01121204
Position gasket (5) and install bolts (4).
Install the O-ring seal and the integral seal on tube (1). Install tube (1).
Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".End By:
Install the valve mechanism cover base.


Parts screw Mercruiser:

35339
 
35339 SCREW, WATER PUMP TO CYLINDER BLOCK (3/4")
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 2165203, 2165208, 257B021JS, 4052110CR, 4111021L1, 4111021TS, 411102KN2, 430B00001, 430L000JS, 4332087N1, 4350100KS, 4350104JS, 4350104KS, 4350111HS, 4350118JS, 4350118KS, 443B0002
45754
 
45754 SCREW, BRACKET AND FLYWHEEL HSG. TO CYLANDER BLOCK (2")
00014332, 01207333, 01402414, 01407333, 01851333, 01854335, 02287333, 02607333, 02608427, 03307332, 03308333, 04544347, 07711346, 08986342, 08987343, 2165203, 2165208, 228801, 260801, 30001854, 37011856, 44031854
20359
 
20359 SCREW, CIRCUIT BREAKER BRACKET TO CYLINDER HEAD (1")
02287333, 02607333, 03302336, 03307332, 04706002, 04707333, 08986342, 2165203, 2165208, 228801, 260801, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430L000JS
46736
 
46736 SCREW, CAM TO CAM LEVER (1/2")
00014332, 02287333, 02607333, 08986342, 2140208, 2165208, 2250507, 228801, 260801, 2888203, 44031854
28635
 
28635 SCREW, WATER TUBE SEALING COVER TO GIMBAL HOUSING (5/8")
00014332, 00019003, 01321017, 01326013, 01701335, 03301310, 03302336, 03307332, 04706002, 04707333, 04708004, 04856332, 04881333, 08986342, 2140208, 2165208, 2250507, 30001854, 32001876, 44031854, 4542067LS, 5000147JS, 5000150DP, 5000165CE, 5111200LP
37268
 
37268 SCREW, TRANSOM PLATE TO GIMBAL HOUSING (4 1/4")
00014332, 00019003, 01321017, 01326013, 2140208, 2165208, 2250507, 5000165CE, 5120150AR, 5220200AS, 91331015
7030
 
7030 SCREW, BRUSH HOLDER ATTACHING (1/2")
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 06661346, 07711346, 08986342, 08987343, 228801, 260801, 3000
34354
 
34354 SCREW, CLAMPING - WATER PUMP BRACKET (1 1/2")
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01701335, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 04706002, 04707333, 04708004, 04881333, 06661346,
Back to top