5087 Mercruiser SCREW, DISTRIBUTOR CAP ATTACHING


5087 SCREW, DISTRIBUTOR CAP ATTACHING Mercruiser 02287333, 02607333, 03302336, 03307332, 08986342, 228801, 260801, 2888203, 44031854 SCREW
5087 SCREW, DISTRIBUTOR CAP ATTACHING Mercruiser
Rating:
28

Buy SCREW, DISTRIBUTOR CAP ATTACHING 5087 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

Mercruiser entire parts catalog list:

02287333 1983
02607333 1983
03302336 1986
03307332 1982
08986342 1982,1983
228801 1981,1982
260801 1981,1982,1987
2888203 1973,1974,1975,1976,1977
44031854 1984

Information:

Introduction
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.If the crankshaft, gear case and/or crank gear are replaced, it is necessary to calibrate the injection timing. The following steps show how to calculate/determine the new injection timing by measuring angular deviation between the crankshaft TDC and Crank Position sensor detected TDC.Note: Once complete the engine ecm must be reprogrammed with the new injection timing value.Follow all steps.Procedure
Illustration 1 g06220548
(1) TC Mark (Flywheel Housing)
(2) TC Mark (Flywheel)
Remove valve cover, and injector and rocker arm. Bring the piston of cylinder 4 to TDC.
Illustration 2 g06220554
(3) Dial Gauge
(4) Valve
(5) O-ring
Remove the #4 exhaust valve bridge arm and valve spring. Insert a small O-ring (5) so the valve does not fall into the cylinder.
Set dial gauge (3) on the tip of the valve (4).
Illustration 3 g06220569
(6) Tri - Square
(7) Flywheel Housing
(8) Flywheel
Illustration 4 g06220573
(7) Flywheel Housing
(8) Flywheel
(9) Reference Line
Turn the flywheel counterclockwise and measure the position where the tip of the valve is the highest.
Stop the flywheel at the position where the tip of the valve is the highest. Put a tri - square (6) on the flywheel housing (7) and the flywheel (8) and draw a reference line (9).Do not drop the valve (4) into the cylinder. When measuring the highest position of the tip of the valve, do not rotate the flywheel clockwise. If you go past the highest point of the valve, back up the flywheel slightly and measure the highest point of the valve. The reference line (9) indicates the TDC of the crankshaft.
Illustration 5 g06220579
Rotation Sensor Signal Interface Unit
Application: Use for reading rotation sensor signal.
(1) 9V Battery
(2) Switch
(3) 3-Terminal Regulator
(4) LED
(5) Clip (Red)
(6) Clip (Black)
(A) for Panasonic
(B) for Denso
(C) for Bosch cam angle
(D) for Bosch crank angle
((E)) Connector Side
(a) +9 V
(b) Signal
(c) GND
(d) +5 V
(e) Signal
(f) GND
Schematic to build Rotation Sensor Signal Interface.
Illustration 6 g06220581
(10) Rotation Sensor Signal Interface (Tool not available. Schematic to build tool available. Refer to Step 6.
(11) Tester
Illustration 7 g06220587
(12) Ground Terminal
(13) Output Terminal
(14) Crankshaft Position Sensor
Connect a connector of the rotation sensor signal interface unit (10) to the crankshaft position sensor (14). Connect each clip of the rotation sensor signal interface unit (10) to the same test lead color of the tester (11). Switch on the rotation sensor signal interface unit (10).
Illustration 8 g06220590
(15) Pulsar Gear
(16) 14th Tooth
(17) Missing Teeth
Turn the flywheel and make sure that the voltage of the crankshaft position sensor goes from 0→ 5 V or 5 → 0 V.
Rotate the flywheel and align the crankshaft position sensor to the part of the pulsar gear (15) that is missing teeth (17). The 14th tooth (16) from the missing teeth is standard.
Slowly turn flywheel counterclockwise and stop flywheel at the point where needle of the tester changes momentarily from 0 → 5 V, the 14th tooth.That point is where the crankshaft position sensor detects TDC.
Illustration 9 g06220608
(18) Crankshaft TDC
(19) Detection Point of Crankshaft Position Sensor TDC
Illustration 10 g06220612
(20) Interval
Set the tri - square (6) on the reference line (9) on the flywheel housing side and mark the detection point of crankshaft position sensor TDC (19) on the flywheel.
Measure the interval (20) between the crankshaft TDC (18)


Parts screw Mercruiser:

34505
 
34505 SCREW, WATER PUMP TO CYLINDER BLOCK (7/8"0
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 06661346, 07711346, 08986342, 08987343, 2165203, 2165208, 228801, 2608
29240
 
29240 SCREW, WIRING HARNESS CLAMP FASTENIGN (5/8")
01206002, 01207333, 01326013, 01406002, 01407333, 02287333, 02607333, 2165203, 2165208, 228801, 260801
29198
 
29198 SCREW, ALTERNATOR BRACE TO ALTERNATOR (7/8")
01207333, 01402414, 01406002, 01407333, 01751347, 02287333, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 06661346, 08986342, 2165203, 2165208, 228801, 257B021JS, 260801, 2888203, 37011856, 40430002S, 40500006T, 40500010T, 405
60835
 
60835 SCREW, EXHAUST SEPARATOR TO GIMBAL HOUSING (5")
02287333, 02607333, 08986342, 228801, 260801, 2888203
52498
 
52498 SCREW, SHIFT BRACKET TO FLYWHEEL HOUISING (1 1/2")
00014332, 01207333, 01402414, 01407333, 02287333, 02297343, 02607333, 02608427, 03302336, 03307332, 04706002, 04707333, 08986342, 08987343, 2250507, 228801, 260801
Back to top