66652 Mercruiser SCREW, MOUNTING BRACKET TO IGNITION COIL


66652 SCREW, MOUNTING BRACKET TO IGNITION COIL Mercruiser 01206002, 01207333, 01326013, 01406002, 01407333, 02287333, 02607333, 03302336, 03307332, 04706002, 04707333, 04856332, 08986342, 2165203, 2165208, 228801, 260801, 2888203 SCREW
66652 SCREW, MOUNTING BRACKET TO IGNITION COIL Mercruiser
Rating:
88

Buy SCREW, MOUNTING BRACKET TO IGNITION COIL 66652 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 34
 

Mercruiser entire parts catalog list:

01206002 1982,1983
01207333 1983
01326013 1983
01406002 1982
01407333 1983
02287333 1983
02607333 1983
03302336 1986
03307332 1982
04706002 1982,1983
04707333 1983
04856332 1982
08986342 1982,1983
2165203 1973,1974,1975,1976,1977
2165208 1978
228801 1981,1982
260801 1981,1982,1987
2888203 1973,1974,1975,1976,1977

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
268-1969 Adapter 1
276-1221 Head 1 Start By:
Remove the cylinder head.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean the bottom mating surface of the cylinder head. Check the depth of the valves below the face of the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder Head Valves" for the correct dimensions.
Place a temporary identification mark on the heads of the valves to identify the correct position. Note: Inlet valves have a recess in the center of the head.
Use a suitable lifting device to position the cylinder head with the valve springs upward. The weight of the cylinder head is approximately 65 kg (143 lb). Note: Ensure that the cylinder head is kept on a clean, soft surface to prevent damage to the machined face.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 1 g01335985
Typical example
Install Tooling (A) in position on the cylinder head to compress appropriate valve spring (3).
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Apply sufficient pressure to Tooling (A) in order to remove valve keepers (1). Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal (4).
Slowly release pressure on Tooling (A).
Illustration 2 g01335986
Remove valve spring retainer (2). Remove valve spring (3).
Repeat steps 4 through 7 for the remaining valves.
Remove Tooling (A).
Remove valve stem seals (4).
Use a suitable lifting device to carefully turn over the cylinder head.
Remove valves (5). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean all components of the cylinder head assembly. Ensure that all ports, all coolant passages, and all lubrication passages in the cylinder head are free from debris. Follow Steps 1.a through 1.d to inspect the components of the cylinder head assembly. Replace any components that are worn or damaged.
Inspect the cylinder head for wear and for damage. Refer to System Operation, Testing and Adjusting, "Cylinder Head Inspect".
Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for further information.
Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder Head Valves" and System Operation, Testing and Adjusting, "Valve Guide - Inspect" for further information.
Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head Valves ".
Inspect valve springs (3) for damage and for the correct length. Refer to Specifications, "Cylinder Head Valves ".
Illustration 3 g01335986
Typical Example
Lubricate the stems of valves (5) with clean engine oil. Install valves (5) in the appropriate positions in the cylinder head. Check the depth of the valves below the face of the cylinder head. Refer to System Operation, Testing and Adjusting, "Valve Depth - Inspect" for more information.
Use a suitable lifting device to carefully turn over the cylinder head. The weight of the cylinder head is approximately 65 kg (143 lb). Note: Ensure that all of the valves remain in place.
Install new valve stem seals (4) onto each of the valve guides. Note: The outer face of the valve guides must be clean and dry before installing valve stem seals (4).
Install valve spring (3) onto the cylinder head. Position valve spring retainer (2) on valve spring (3).
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 4 g01335985
Install Tooling (A) in the appropriate position on the cylinder head to compress valve spring (3).


Parts screw Mercruiser:

34471
 
34471 SCREW, WATER PUMP TO CYLINDER BLOCK (1 1/2")
01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 2165203, 2165208, 4111021L1, 4111021TS, 4111021UT, 4111021UU, 411102KN2, 41510P1UE, 430B00001, 430L000JS
46718
 
46718 SCREW, WIRING HARNESS PLATE TO MOUNTING BRACKET(3/4")
01206002, 01207333, 01326013, 01406002, 01407333, 02287333, 02607333, 03302336, 03307332, 04706002, 04707333, 04856332, 08986342, 2165203, 2165208, 228801, 260801, 2888203, 44031854
53016
 
53016 SCREW, END CAP/CONNECTOR TO EXHAUST MANIFOLD (1 1/4")
03302336, 03307332, 04706002, 04707333, 08986342, 2888203
Back to top