821045 10 Mercruiser SCREW, (M5 x 10)


821045 10 SCREW, (M5 x 10) Mercruiser 5P4AB04HH, 5P4AB04IH SCREW
821045 10 SCREW, (M5 x 10) Mercruiser
Rating:
33

Buy SCREW, (M5 x 10) 821045 10 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 27
 

Compatible models:

5P4AB04HH   5P4AB04IH   Mercruiser

Mercruiser entire parts catalog list:

5P4AB04HH 2007,2008
5P4AB04IH 2008

Information:


Illustration 1 g06391426
Front of the engine
Illustration 2 g06391460
Marks for tightening main bearings
Table 1
Item Qty Part Specification Description
1 - - Use the following procedure to tighten the studs:
1. Apply Loctite® Hi-Temp flange sealant.
2. Tighten the stud with coated pipe threads into the cylinder block.
2 - - During assembly, the top of face of the cylinder block, both sides of plate gasket and bottom surface of spacer plate must be free of fuel, oil, water, gasket adhesives, assembly compounds, and any other contaminants.
3 - -
4 3 - Tighten the taperlock studs to 35 5 N m (26 4 lb ft).
5- 4 - Use the following procedure to tighten the taperlock studs:
1. Before assembly, apply Loctite® 536 pipe sealant on the threads of the taperlock studs.
2. Tighten the taperlock plugs to 80 15 N m (59 11 lb ft).
6 - - Use the following procedure to install the crankshaft cap:
1. Apply clean engine oil on the threads of the bolts (8). Loosely install the bolts (8).
2. Apply clean engine oil on the threads of the side bearing cap bolts (6) and the washers. Loosely install the side bearing cap bolts (6) and the washers.
3. Tighten tab end of the main bearing cap bolt (8) to 258 14 N m (190 10 lb ft).
4. Tighten opposite end of the main bearing cap bolt (8) to 258 14 N m (190 10 lb ft).
5. Put a mark on each bolt (8) and each crankshaft cap (7). as shown in Illustration 2.
6. Again, tighten opposite end of the main bearing cap bolt from the mark to an additional angle (D6) of 120 5 degrees.
7. Again, tighten tab end of the main bearing cap bolt from the mark to an additional angle (D6) of 120 5 degrees.
8. Tighten the side bearing cap bolts (6) that are at the opposite end of the main bearing cap to 80 10 N m (60 7 lb ft).
9. Tighten the side bearing cap bolts (6) that are at the tab end of the main bearing cap to 80 10 N m (60 7 lb ft).
10. Again, tighten the side bearing cap bolts (6) that are at the opposite end of the main bearing cap to 80 10 N m (60 7 lb ft).
11. Again, tighten the side bearing cap bolts (6) that are at the tab end of the main bearing cap to 80 10 N m (60 7 lb ft).
7 - -
8 - -
D1 - - Thickness of the spacer plate is 8.585 0.025 mm (0.3380 0.0010 inch).
D2 - - Thickness of plate gasket that is between cylinder block and spacer plate is 0.195 0.028 mm (0.0077 0.0011 inch).
D3 - - Extension of the dowels on the left bank and right bank from the cylinder block is 18.5 0.5 mm (0.73 0.02 inch).
D4 - - Bore in the cylinder block for main bearing is 129.891 0.013 mm (5.1138 0.0005 inch).
D5 - - The width of the slot for the main bearing caps is 236.00 0.05 mm (9.291 0.002 inch).
Width of main bearing cap is 235.500 0.025 mm (9.2716 0.0010 inch).
Illustration 3 g06391476
Right side of the engine
Table 2
Item Qty Part Specification Description
D7 - - Extension of dowels from the rear face of the cylinder block and from the front face of the cylinder block is 19.0 0.5 mm (0.75 0.02 inch).
Illustration 4 g06391484
Table 3
Item Qty Part Specification Description
D8 - - The distance from the centerline of the crankshaft bearing bore to the top of the cylinder block is 419.10 0.15 mm (16.500 0.006 inch).
D9 - - The distance from the centerline of the crankshaft bearing bore to the bottom of the cylinder block is 165.10 0.10 mm (6.500 0.004 inch).
Illustration 5


Parts screw Mercruiser:

40089 16
 
40089 16 SCREW, (M8 x 16) Stainless Steel
41000001S, 41000008E, 5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
821300 25
 
821300 25 SCREW, (M6 x 25)
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 41510P1UE, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8U
40003 27
 
40003 27 SCREW, (M6 x 14)
4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE, 5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
818934 14
 
818934 14 SCREW, (M8 x 14)
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
818934 20
 
818934 20 SCREW, (M8 x 20)
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
824948 30
 
824948 30 SCREW, (M6 x 30)
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
19937 16
 
19937 16 SCREW, (M6 x 16)
5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
8M0007529
 
8M0007529 SCREW
5P4AB04HH, 5P4AB04IH
Back to top