882427 Mercruiser SCREW, (M12 x 47), Cam Pulley


882427 SCREW, (M12 x 47), Cam Pulley Mercruiser 4V71222ND, 4V71222PD, 4V71222TD SCREW
882427 SCREW, (M12 x 47), Cam Pulley Mercruiser
Rating:
48

Buy SCREW, (M12 x 47), Cam Pulley 882427 Mercruiser genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$1,469.86
 

07-10-2017
136.00[61.20] pounds
Justrite M: Justrite Manufacturi
Justrite 882427 18 Gauge Steel 1 Door Self Close Under Fume Hood Flammables Safety Storage Cabinet with Right Hinge, 15 Gallon Capacity, 24" Width x 35-3/4" Height x 21-5/8" Depth, Light Neutral
Fully welded, double wall 18 gauge steel with 1-1/2-inches insulating air space||U-Loc handle comes with double key set or accepts optional padlock||Stainless steel, 3-point bullet self-latching system||Leak proof 2-inches bottom sump to capture spills||One SpillSlope shelf adjustable on 3-inches centers, highly reflective Haz-Alert hazard labeling at top and bottom
Number on catalog scheme: 9
 

Compatible models:

Mercruiser entire parts catalog list:

4V71222ND 1998
4V71222PD 1998
4V71222TD 1998

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     8S-6691     Cylinder Head Repair Stand     1    
B     9U-6195     Valve Spring Compressor Gp     1    
C     5P-1720     Seal Pick     1    Start By:
Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Note the location and orientation of all components for assembly purposes.
Clean the bottom face of the cylinder head. Check the depth of the valves below the face of the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder Head Valves" for the correct dimensions.
Place a temporary identification mark on the heads of the valves in order to identify the correct position.
Illustration 1 g01376164
Typical Example
Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the valve springs upward. The weight of cylinder head (1) is approximately 70 kg (155 lb).Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent damage to the machined face.
Illustration 2 g01376174
Illustration 3 g01376184
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Install Tooling (B) on cylinder head (1) in order to compress valve spring (5) .
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not compress the spring so that valve spring retainer (4) touches valve stem seal (6) .
Slowly release the pressure on Tooling (B) .
Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2) .
Use Tooling (C) in order to remove valve stem seal (6) .
Repeat Steps 4 through 7 for the remaining valves.Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
A     8S-6691     Cylinder Head Repair Stand     1    
B     9U-6195     Valve Spring Compressor Gp     1    
D     312-8755     Valve Stem Seal Installer     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Clean all components of the cylinder head assembly. Ensure that all ports, all coolant passages and all lubrication passages in the cylinder head are free from debris. Follow Steps 1.a through 1.d in order to inspect the components of the cylinder head assembly. Replace any components that are worn or damaged.
Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting, "Cylinder Head Inspect".
Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for further information.
Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further information.
Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head Valves ".
Inspect valve springs (5) for damage and for the correct length. Refer to Specifications, "Cylinder Head Valves ".
Illustration 4 g01376184


Parts screw Mercruiser:

882323
 
882323 SCREW, (M10 x 22), With Lockwasher
4V71222ND, 4V71222PD, 4V71222TD
882419
 
882419 SCREW, (M10 x 40)
4V71222ND, 4V71222PD, 4V71222TD
882371
 
882371 SCREW, (M11 x 73)
4V71222ND, 4V71222PD, 4V71222TD
882313
SCREW, (M6 x 16)
882313 SCREW, (M6 x 16)
4V71222ND, 4V71222PD, 4V71222TD
882320
 
882320 SCREW, (M8 x 18) (M8 x 18)
4V71222ND, 4V71222PD, 4V71222TD
882322
 
882322 SCREW, (M10 x 20), With Lockwasher
4V71222ND, 4V71222PD, 4V71222TD
882350
 
882350 SCREW, (M14 x 27), Flange
4V71222ND, 4V71222PD, 4V71222TD
882327
 
882327 SCREW, (M8 x 35), With Plain and Lockwasher
4V71222ND, 4V71222PD, 4V71222TD
Back to top