882428 Mercruiser SCREW, (M8 x 23)


882428 SCREW, (M8 x 23) Mercruiser 4V71222ND, 4V71222PD, 4V71222TD SCREW
882428 SCREW, (M8 x 23) Mercruiser
Rating:
18

Buy SCREW, (M8 x 23) 882428 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Compatible models:

Mercruiser entire parts catalog list:

4V71222ND 1998
4V71222PD 1998
4V71222TD 1998

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     278-4138     Fuel System Protection Gp (1)     1    
( 1 ) This tool can only be used one time. Start By:
Remove the fan drive. Refer to Disassembly and Assembly, "Fan Drive - Remove and Install".Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be cleaned. Cleaning the components thoroughly will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all hoses, on all hose assemblies, on all harness assemblies, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. Plugging all hose assemblies helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Contact with high pressure fuel may cause personal injury or death. Wait 60 seconds after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Note: Before opening the fuel system, the engine must be turned off for at least one minute.Note: Use Caterpillar Electronic Technician (ET) to verify that the fuel system pressure is at zero before opening the fuel system.Note: Use Tooling (A) after any fuel line has been disconnected.
Illustration 1 g01375105
Illustration 2 g02723312
(2) Fuel injection pump drive gear (3) Idler gearNote: Mark the teeth on pump drive gear (2) and idler gear (3) for installation purposes.
Remove cover (1) .
If you are reusing pump drive gear (2) , mark pump drive gear (2) and idler gear (3) .
If replacing pump drive gear (2) or a problem is encountered, align the "33" Mark on fuel injection pump drive gear (2) with the "3" Mark on idler gear (3) by rotating the engine.Note: The No. 1 cylinder is at the top center position when the "33" Mark and the "3" Mark are in alignment.
Illustration 3 g01375153
Disconnect hose assembly (4) .
Remove nut (5) .
Disconnect hose assemblies (6) and remove the washers. Discard the washers.
Disconnect harness assembly (7) .
Remove tube assembly (9) and remove bracket assembly (8) .
Illustration 4 g01375195
Loosen clamp (12) and disconnect hose (13) .
Remove fitting (11) in order to disconnect tube assembly (10) and remove the washers. Discard the washers.
Illustration 5 g01375184
Remove tube assembly (14) .
Disconnect harness assembly (15) .
Remove bolt (16) in order to remove hose assembly (17) and the washers. Discard the washers.
Remove bolt (19) in order to disconnect hose assembly (18) and the washers. Discard the washers.
Remove bolt (20) . Remove tube assembly (10) and the washers. Discard the washers.
Illustration 6 g01375221
Remove bolts (22) .
Remove two bolts (23) (not shown).
Remove bolts (24) .
Remove fuel injection pump (21) a


Parts screw Mercruiser:

882323
 
882323 SCREW, (M10 x 22), With Lockwasher
4V71222ND, 4V71222PD, 4V71222TD
882419
 
882419 SCREW, (M10 x 40)
4V71222ND, 4V71222PD, 4V71222TD
882371
 
882371 SCREW, (M11 x 73)
4V71222ND, 4V71222PD, 4V71222TD
882313
SCREW, (M6 x 16)
882313 SCREW, (M6 x 16)
4V71222ND, 4V71222PD, 4V71222TD
882320
 
882320 SCREW, (M8 x 18) (M8 x 18)
4V71222ND, 4V71222PD, 4V71222TD
882322
 
882322 SCREW, (M10 x 20), With Lockwasher
4V71222ND, 4V71222PD, 4V71222TD
882350
 
882350 SCREW, (M14 x 27), Flange
4V71222ND, 4V71222PD, 4V71222TD
882327
 
882327 SCREW, (M8 x 35), With Plain and Lockwasher
4V71222ND, 4V71222PD, 4V71222TD
Back to top