885526 75 Mercruiser SCREW, (M8 x 75)


885526 75 SCREW, (M8 x 75) Mercruiser 41000001S, 41000008E SCREW

Buy SCREW, (M8 x 75) 885526 75 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Compatible models:

41000001S   41000008E   Mercruiser

Mercruiser entire parts catalog list:

Information:

1. Remove bolts (2), nut (3), cover (1) and the gasket from the engine front housing. 2. Remove bolts (4), retainer (5) and automatic timing advance (6) from the engine.Install Automatic Timing Advance
1. Put automatic timing advance (1) in position in the front housing and install the retainer and the bolts. Tighten the bolts finger tight until there is a small amount of friction (slight drag) between the retainer and the timing advance unit. This will prevent movement (backlash) when the gears are turned to the correct timing position. 2. Remove timing bolt (2), cover (3) and plug (4). 3. Use tool (A) to turn the engine in a counterclockwise direction (as seen from the flywheel end of the engine) until timing bolt (2) can be installed into the flywheel. The No. 1 piston must be at top center on the compression stroke. If the hole in the flywheel is turned beyond the hole in the flywheel housing, turn the flywheel back (clockwise) a minimum of 30° beyond the hole in the flywheel before turning counterclockwise toward the hole again. This will prevent a timing error caused by play in the timing gears.4. To see if No. 1 piston is on the compression stroke, look at the valves of No. 1 cylinder. The valves will be closed if No. 1 cylinder is on the compression stroke. You should be able to move the rocker arms up and down with your hand.If No. 1 piston is not on the compression storke, turn the flywheel 360° and install the timing bolt.
Typical Example5. Remove the plug from the front of the fuel injection pump housing. Install tool (B) through the hole in the pump housing. If the timing is correct, tool (B) can be installed into the notch in the fuel injection pump camshaft.6. If tool (B) can not be installed into the notch of the camshaft, remove it and the timing bolt from the flywheel.7. Repeat Step 3 and turn the flywheel an additional 360°. Repeat Step 4.8. Tighten the bolts that hold the automatic timing advance to a torque of 25 N m (18 lb.ft.); then tighten the bolts to a torque of 136 7 N m (100 5 lb.ft.). Remove the timing bolt (2) from the flywheel.9. Turn the engine two complete revolutions and check the timing again. If tool (B) will not go into the notch of the fuel injection pump camshaft, do Steps 1 through 8 again. 10. If a replacement of stud (6) is necessary, put 9S3263 Thread Lock on the threads of the new stud. Install it in the engine front housing until it is 73.2 mm (2.88 in.) above the outside surface.11. Put the gasket and cover (5) on the engine front housing and install the bolts and the nut that hold it.END BY:a) install fan drive and fan belt tightenerDisassemble Automatic Timing Advance
START BY:a) remove automatic timing advance 1. Remove ring (1) and gear assembly (2) from the flange assembly. 2. Remove the slides from the weights.3. Remove springs (4) and weights (3) from the flange assembly.Assemble Automatic Timing Advance
1. Put weights (2) in position in flange assembly (1) as shown.2. Install springs (3) in flange assembly (1). 3. If pistons (6) were removed from the gear assembly because of wear, use new parts for replacement. Install new pistons (6) until they are 11.05 .13 mm (.435 .005 in.) above the inside surface of gear assembly (4). Move the metal (peen) on the outside surface of gear assembly (4) in four places around each piston to hold them in position.4. Use 1P808 General Purpose Lubricant to hold slides (5) in position on gear assembly (4).5. Install gear assembly (4) on flange assembly (1). Make sure slides (5) fit in the grooves of the weights.6. Install the ring that holds gear assembly (4) to the flange assembly.END BY:a) install automatic timing advance


Parts screw Mercruiser:

58640
 
58640 SCREW, TOP COVER TO DRIVE SHAFT HOUSING (1 1/4")
00014332, 01207333, 01402414, 01407333, 01701335, 01751347, 01851333, 01854335, 02287333, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 04707333, 04708004, 04881333, 06661346, 07711346, 08986342, 08987343, 2140208, 2165208, 22
40108 35
 
40108 35 SCREW, (M10 x 35) Hex Flange - Stainless Steel
41000001S, 41000008E, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
40107 35
 
40107 35 SCREW, (M8 x 35)
40280002D, 40420002D, 41000001S, 41000008E, 4S42028TT, 4S420P8UE
824459110
 
824459110 SCREW, (M8 x 110) Stainless Steel
41000001S, 41000008E, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE
855939 12
 
855939 12 SCREW, (M6 x 12)
41000001S, 41000008E
821300 25
 
821300 25 SCREW, (M6 x 25)
40430002S, 40500006T, 40500010T, 40500010U, 40500120U, 41000001S, 41000008E, 41510P1UE, 424106LRS, 424106LTT, 424106LUS, 424106PUU, 444106LPS, 444236HRS, 4M4102LPS, 4M4102LRS, 4M4102LTS, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8U
898101834
 
898101834 SCREW , (M6 x 18)
41000001S, 41000008E
40089 30
 
40089 30 SCREW, (M8 x 30) Stainless Steel
41000001S, 41000008E, 5P4AB04HH, 5P4AB04IH, 5P4AZ54JH
Back to top